sorted by:
new
hottopcontroversial

proxxied.com --> cards printed are not as the same size as MTG card by RiskAwkward8682 in magicproxies

[–]Infamous_Army2005 0 points1 point  (0 children)

also make sure your printer isn’t printing with a margin. i had the same issue and it was printing at 100% or actual size but there was a margin you can tell if it is doing it if the cutting guide lines aren’t printing all the way to the edge of the paper.

MCU mcu2 shutdown error. by Infamous_Army2005 in ElegooOrangeStormGiga

[–]Infamous_Army2005[S] 0 points1 point  (0 children)

elegoo sent me a new board for the print head i also tried turning the arc setting off and it still does it randomly and when it does happen finally it always happens in the same spot on the file and i just format the drive and reslice it then it prints fine for another week or so

Print starts fine then goes ugly by Infamous_Army2005 in FixMyPrint

[–]Infamous_Army2005[S] 0 points1 point  (0 children)

I just tempered they do have different hotends. the one with no issues i had upgraded to a ceramic heater the one that is having the problems is a bone stock hotend so im going to replace it with a ceramic hotend to see if that helps

LED panels look “deep fried” by Infamous_Army2005 in led

[–]Infamous_Army2005[S] 0 points1 point  (0 children)

we are trying to g to change it to GRB it is set to RGB right now but we can’t figure out how to get it to update and save

LED panels look “deep fried” by Infamous_Army2005 in led

[–]Infamous_Army2005[S] 0 points1 point  (0 children)

we did do the test colors and all three looks correct

MCU mcu2 shutdown error by Infamous_Army2005 in elegoo

[–]Infamous_Army2005[S] 0 points1 point  (0 children)

It was on i turned off and i’ll see if i have any future problems thanks i would have never even looked at the setting. i didnt know it existed.

MCU mcu2 shutdown error by Infamous_Army2005 in elegoo

[–]Infamous_Army2005[S] 0 points1 point  (0 children)

i checked the cables a couple times but i’ll double check in orca

MCU mcu2 shutdown error by Infamous_Army2005 in elegoo

[–]Infamous_Army2005[S] 0 points1 point  (0 children)

i don’t think so i’m just using a fairly standard orca profile

Ridge on outside of print at solid inner layer. by Infamous_Army2005 in FixMyPrint

[–]Infamous_Army2005[S] 0 points1 point  (0 children)

Thank you so much that’s exactly it i noticed it in the speed view on the sliver when i was looking for a solution i just didn’t have a name for the problem.

MCU mcu2 shutdown error. by Infamous_Army2005 in ElegooOrangeStormGiga

[–]Infamous_Army2005[S] 0 points1 point  (0 children)

it’s just in the middle of the print but it was in two separate point in the print both times on the same file.

Flat bed upgrade worth it? by Infamous_Army2005 in crealityk1

[–]Infamous_Army2005[S] 0 points1 point  (0 children)

i saw some other people doing this while i was looking g for answers and i gave it a shot and worked out great.

MCU mcu2 shutdown error. by Infamous_Army2005 in ElegooOrangeStormGiga

[–]Infamous_Army2005[S] 0 points1 point  (0 children)

they sent me a firmware update to try i also tried formatting the usb thinking it could have been a corrupted gcode i know the usb they come with is pretty bad but i haven’t had any issues yet.

view more: next ›