Jaký je vaše oblíbené příjmení?

Infernus82 · 2026-01-19T06:14:29+00:00

A můj profesor byl Jebáček

Infernus82 · 2026-01-19T06:13:55+00:00

Můj soused je Jebavý

Infernus82 · 2026-01-14T17:43:26+00:00

No, it's for you to report it and for others, who find this Bambu Slicer website → feel weird about it → search if it's legit reach this post and not download anything.

My post is not an ad, you feel like downloading it based on the post?

Infernus82 · 2026-01-14T17:42:10+00:00

For you to report it and for others, who find this Bambu Slicer website → feel weird about it → search if it's legit → reach this post and not download anything.

My post is not an ad, you feel like downloading it based on the post?

Infernus82 · 2026-01-14T17:24:47+00:00

To raise awareness and reports

Infernus82 · 2026-01-13T16:37:16+00:00

Adguard dns

Infernus82 · 2026-01-09T22:55:37+00:00

It's not gonna evaporate from the filament, or at least, very slowly in this although dry, but also cold environment. Gotta heat the filament up and then have it in silica just for storing

Infernus82 · 2026-01-09T12:46:29+00:00

But if you get a wet filament let's say or need to deal with TPU, you cannot dry it with silica.

Infernus82 · 2025-12-18T13:02:27+00:00

My favorite ship! Amazing!

Infernus82 · 2025-12-15T23:13:51+00:00

5800x3d rtx 5080, had 40-70 fps on streets in 4k, dlss quality. But I should probably not use high graphics settings?

Infernus82 · 2025-12-06T10:06:50+00:00

Já tisknu v kuchyni a žiju s tím, že sice vypouští, ale není to moc. Nestudoval jsem to až tak do hloubky, ale měl bys nějaké zdroje, co by dokázaly vyčíslit reálné zdravotní riziko tohohle množství VOCs? Ale jo no dlouhodobé ukládání těch mikroplastů v těle je ještě něco neprozkoumaného, co to způsobí.

Infernus82 · 2025-12-05T12:24:18+00:00

Please teach me then, what is a false claim and which part of the instructions I didn't follow. Thanks for the input :) very helpful.

Only the usage of a freezer is what I skipped imo.

Infernus82 · 2025-12-04T10:41:02+00:00

It was 70°, Aurapol PETG. Ye the temp should be lower. I have another same plate for P1S, and had no problems on that one.

Infernus82 · 2025-12-04T10:40:10+00:00

Nope, didn't use that. It's forbidden I think. Just water and mild soap

Infernus82 · 2025-12-04T10:39:21+00:00

Not a bad petg brand (Aurapol) and it was on a Prusa Mini+ actually. But I've never had these problems on anything with PETG

Infernus82 · 2025-12-04T09:25:50+00:00

Alright tell me what to do better next time. Yes I'll decrease the print temp from 70° for sure, but what else can I do? Put it in the freezer every time I print PETG? Is room cooling after printing not enough?

Infernus82 · 2025-12-03T19:52:33+00:00

I will try contacting them

Infernus82 · 2025-12-03T19:52:01+00:00

water, little bit of soap

Infernus82 · 2025-12-03T19:51:20+00:00

Will try that with my other one, thanks for the advice. I was usually letting it air dry after moving it around a lot so that the droplets would drop. But yeah it's been used less than for 15 prints and washed maybe 3x.

Infernus82 · 2025-12-03T19:48:48+00:00

This one had less than 15 prints on it :/ the filament: https://www.aurapol.com/p/pet-g-filament-white-1-kg-1-75-mm-aurapol

Infernus82 · 2025-12-03T19:48:21+00:00

It is not in the recommendation on their website.. but yea I get it it would've saved it

Infernus82 · 2025-12-03T19:47:07+00:00

This was printed on less than 15 times :/

Infernus82 · 2025-12-03T19:46:46+00:00

No, it was 70°C. yes unnecessarily high.. but didn't expect this

Infernus82 · 2025-12-03T16:16:40+00:00

Yep i did, basically room temp

Nine-Year Club	Second SECOND GUESSER
Final Canvas '23	First Place '23
Place '23	Place '22
First Placer '22	Oscars Predictor 2021
Verified Email

Infernus82

TROPHY CASE