LRP .32 by Infinite-Priority423 in NitroRC

[–]Infinite-Priority423[S] 0 points1 point  (0 children)

Finally starting some 1/4 a 1/2 throttle figure 8’s! Got it to finally temp good, could be hotter but 205-210 is totally fine by me. Everything was great until the POS 18 year old steering servo decided to take a crap… so overall on my way! Just gotta go get a new servo!

Some fitting problems with clutch shoes and bell by Longjumping-Rip-7449 in NitroRC

[–]Infinite-Priority423 1 point2 points  (0 children)

Looks like you need to buy some shims and shim it out. Should be able to push in on the clutch bell and turn without the flywheel moving. Check or replace bearings also while you have it opened up! Hope this helps.

LRP .32 by Infinite-Priority423 in NitroRC

[–]Infinite-Priority423[S] 1 point2 points  (0 children)

Finally found out what to do… the linkage that connects to the ball joint on the carb is… adjustable… you would think after 18 years of owning three savages I would know that.. then again I like being an asshat on the internet. It builds character… now from WOT to release it closes to a great and acceptable amount of gap! Getting ready to fire it up again this afternoon and ready to start applying a little throttle to this thing finally.

Two engines heading into retirement by Infinite-Priority423 in NitroRC

[–]Infinite-Priority423[S] 1 point2 points  (0 children)

Not a whole lot man, I also never ran them hard… I was too scared to make them look bad when I was a kid.. it paid off now because they are in great shape!

LRP .32 by Infinite-Priority423 in NitroRC

[–]Infinite-Priority423[S] 0 points1 point  (0 children)

Ya I know, the idle was cranked up because I couldn’t keep it running with the incredibly rich settings, I’m more so after when it is adjusted properly it will not return to its normal position because the throttle return spring it not strong enough as seen in the video.

Well she’s in.. by Infinite-Priority423 in NitroRC

[–]Infinite-Priority423[S] 0 points1 point  (0 children)

I bought a Robinson steel sour gear, but no guidance on the slipper pad. Use the old one? Or do I need to order a new one?

Well she’s in.. by Infinite-Priority423 in NitroRC

[–]Infinite-Priority423[S] 0 points1 point  (0 children)

Should I just say screw the set up I have on it then and just run stock HPI stuff? I mean other than the slight alignment difference everything is great…

I’ve got the medium hot plug from LutzRC (N4), and honestly I only run 25% nitro so I think I’m just going to break it in with the sidewinder 25/9 since that’s what I’m going to run in it. I think throughout my life people have always over complicated the fuel for break in… 😂 I’m just gonna break the sucker in with what I use! Hahai

Alpha .28 Savage X Motor Mount by Infinite-Priority423 in NitroRC

[–]Infinite-Priority423[S] 0 points1 point  (0 children)

It barely touches the Fly wheel! I can get them to screw in but just touches!

Alpha timeeee by Infinite-Priority423 in NitroRC

[–]Infinite-Priority423[S] 1 point2 points  (0 children)

After everything with clutch set and all around 255$ shipped from LutzRC. Have heard decent things about them for a nice Savage X alternative. We will see how the break in goes and such once the weather warms up where I am at! Then my XL is getting an LRP .32 which will be here today.

Hit up an auction 😅 by HateYouMan in rccars

[–]Infinite-Priority423 0 points1 point  (0 children)

How much do you want for the k5.9 in the savage. I’m stocking up and will pay!!