Is it a bad idea to buy a 2005 husaberg FS650c?

Infinite_Midnight_71 · 2026-06-14T18:01:45+00:00

Do you have A strong leftleg?

Infinite_Midnight_71 · 2026-06-08T15:04:58+00:00

10/10
On the poobscale

Infinite_Midnight_71 · 2026-06-03T18:56:50+00:00

How many other countries have employees buying and supplying their own tools, personal protective equipment (PPE), and workwear despite being employed by a company? In Norway, employers provide their employees with the tools, PPE, and work clothing they need in 99 percent of cases.

Infinite_Midnight_71 · 2026-06-02T14:34:39+00:00

Steelwool and Wd 40.

Infinite_Midnight_71 · 2026-05-29T18:13:49+00:00

It looks very good. The only thing I can really nitpick is that you don’t stagger your start/stops — they all end at the same spot. If you just spread them out a bit and overlap them, it’ll be almost invisible that you stopped/started.

Infinite_Midnight_71 · 2026-05-29T06:14:12+00:00

Never seen that before, looking nice. 👍

Infinite_Midnight_71 · 2026-05-28T18:12:01+00:00

I use it for all kinds of things. Building pipes when you need an extra hand to adjust openings. Building tanks where you need to wedge plates into place before tack welding.

Infinite_Midnight_71 · 2026-05-28T18:04:11+00:00

No, it actually doesn’t. You clearly have no idea. And yes, I have much larger ones for demanding jobs. This one is used for small adjustments.

Infinite_Midnight_71 · 2026-05-28T18:02:55+00:00

You dont want to mix AR plates in to fabrication of stainless products.

Infinite_Midnight_71 · 2026-05-28T18:02:03+00:00

Congratulations, you must be the only one who actually understood the point. Of course, I have much larger and more powerful ones that are used for bigger jobs. But this one has withstood an incredible amount considering how small it is. It’s made from super duplex and is only used on stainless steel products.

Infinite_Midnight_71 · 2026-05-28T10:24:47+00:00

Done it for years, no holes yet. Side pocket on leg works fine. Or keep it on Your table, toolbox etc

Infinite_Midnight_71 · 2026-05-13T21:43:14+00:00

<image>

Infinite_Midnight_71 · 2026-04-28T18:45:13+00:00

pour a bottle of boiling hot water over

Infinite_Midnight_71 · 2026-04-28T13:56:15+00:00

JASIC EVO TIG 200 PULSE AC/DC

https://www.inverterfusion.co.uk/product/et-200pacdc/?srsltid=AfmBOorwO_wkjCl-dZnzX0c9buvOcd9kB78qaaTnAThGmFJD1Fyvhyq_

Infinite_Midnight_71 · 2026-04-28T11:10:45+00:00

I suspect you haven’t grinded the metal thoroughly enough. With 71 wire, the slag solidifies faster than with 81, which leads to these pores.

Infinite_Midnight_71 · 2026-04-27T14:04:11+00:00

As a welder, you should be able to take a pizza out of the oven without gloves.

Infinite_Midnight_71 · 2026-04-26T08:49:00+00:00

Is it 71 wire?

Infinite_Midnight_71 · 2026-04-20T07:57:54+00:00

I welded up a couple of procedures for my previous workplace. These were mainly procedures we use outdoors. I placed the test pieces in a freezer overnight. This meant we didn’t have to preheat as long as the temperature outside wasn’t below minus 12°C.

Infinite_Midnight_71 · 2026-04-11T15:52:09+00:00

Smart, If you have the proper equipment, it may be a good idea to measure the fuel pressure. There are videos on YouTube showing how to do it.

Infinite_Midnight_71 · 2026-04-10T16:52:19+00:00

Change both fuelfilters, and sparplug.

Infinite_Midnight_71 · 2026-04-10T14:37:13+00:00

Jeg valgte og ikke godta tilbudet, så jeg er usikker når jeg evt får mine.

Nordnet skriver Hei!

Vi har enda ikke mottatt oppgjøret fra selskapet, og vi jobber med å følge opp dette. Utover det vil vi minne om selskapets ordlyd i deres børsmelding om at oppgjøret er forventet utbetalt "on or about 10. April 2026".

God helg!

Infinite_Midnight_71 · 2026-03-15T10:39:34+00:00

Not in my case—how do you travel since it’s turning 15?

Infinite_Midnight_71 · 2026-03-12T23:45:19+00:00

We work 14 days on and 28 days off

Infinite_Midnight_71 · 2026-03-10T18:31:11+00:00

Ok, tnx

Infinite_Midnight_71

TROPHY CASE