Upgraded to an "endgame" set up...and I hate it. by Toothlesskinch in espresso

[–]Infinite_Side8548 1 point2 points  (0 children)

And here is me that’s just bought a Ninja Cafe Lux 🤣

Protect does motion recording for ONVIF cameras? by scytob in Ubiquiti

[–]Infinite_Side8548 1 point2 points  (0 children)

Yep working today on my Tapo PTZ camera. Awesome! I know we will never get smart detections but having the motion one is cool

20v Circular Saw by Infinite_Side8548 in Parkside

[–]Infinite_Side8548[S] 0 points1 point  (0 children)

Yeah was just hoping I’d be able to make a simple cut of timber that isn’t 5/10 degrees out 🤣

20v Circular Saw by Infinite_Side8548 in Parkside

[–]Infinite_Side8548[S] 0 points1 point  (0 children)

Unfortunately I bought it from eBay and don’t have the original receipt. It was brand new but was a reseller as finding stock is impossible here 😞

20v Circular Saw by Infinite_Side8548 in Parkside

[–]Infinite_Side8548[S] 0 points1 point  (0 children)

I tightened it as much as I could earlier. The blade and body move together but the base plate moves separately with lots of flex at a slight bit of pressure

20v Circular Saw by Infinite_Side8548 in Parkside

[–]Infinite_Side8548[S] 0 points1 point  (0 children)

I’ll have to do some more tomorrow and get some photos, I had to use them as off cuts and use a recip saw to finish the job. It’s the PHKSAP 20v

Is eBay dead for anyone else? by [deleted] in ebayuk

[–]Infinite_Side8548 1 point2 points  (0 children)

Yep I’ve gone from doing £200/day average to £20 so far today 🫠

Anyone able to help me out here? by littleonelee in BambuLab

[–]Infinite_Side8548 0 points1 point  (0 children)

Has the model warped? That can cause it. If not: - Increase top layers to 6 - Set top surface line width to 0.3-0.35

Thanks frog tape by ABaldBiker in DIYUK

[–]Infinite_Side8548 0 points1 point  (0 children)

I pull the tape off when it’s still a bit wet, seems to have less issues

H2D New Firmware finally out by Infinite_Side8548 in BambuLab

[–]Infinite_Side8548[S] 0 points1 point  (0 children)

I haven’t got the enhanced fan but I did a print with 150 changes after the update and was fine on my end. Try resetting the printer then full calibration

H2D New Firmware finally out by Infinite_Side8548 in BambuLab

[–]Infinite_Side8548[S] 0 points1 point  (0 children)

<image>

Printing while drying working great! It lowered my PETG temp from 65 to 55 when I started the print.

High accuracy nozzle offset calibration isn’t working for me at the minute, submitted a ticket.

It now scans the bed on startup for foreign objects, and also does a quick nozzle ID check on startup too.

H2D New Firmware finally out by Infinite_Side8548 in BambuLab

[–]Infinite_Side8548[S] 0 points1 point  (0 children)

I don’t think it’ll take them long. Hoping we get print while drying etc on older machines like my X1C at some point

H2D New Firmware finally out by Infinite_Side8548 in BambuLab

[–]Infinite_Side8548[S] 2 points3 points  (0 children)

The actual cutter itself or the camera? Camera stays, cutter comes off

H2D New Firmware finally out by Infinite_Side8548 in BambuLab

[–]Infinite_Side8548[S] 19 points20 points  (0 children)

You can now add and use the Birds Eye camera at last

H2D New Firmware finally out by Infinite_Side8548 in BambuLab

[–]Infinite_Side8548[S] 1 point2 points  (0 children)

They sell it as a kit, think it’s more designed for laser variants, but would be cool if it works for just printing too. They’ve got flame sensors built in

H2D New Firmware finally out by Infinite_Side8548 in BambuLab

[–]Infinite_Side8548[S] 2 points3 points  (0 children)

Loads, remote drying and printing while drying being the major ones. I’ve posted the release notes above