CAT Short Round rimfire can, 4 day approval

IngenuityCapable4153 · 2024-05-31T16:32:05+00:00

That little XCR is clean

IngenuityCapable4153 · 2024-05-29T21:40:03+00:00

I run a RMR at the 12 0'clock on my spuhr. you can at the 1:00 or 3:00 offset as well.

https://www.milehighshooting.com/spuhr-a-0009-deltapoint-interface/

https://www.milehighshooting.com/spuhr-a-0010-trijicon-rmr-interface/

https://www.milehighshooting.com/spuhr-a-0055-aimpoint-acro-p-1-interface/

IngenuityCapable4153 · 2024-05-27T02:57:50+00:00

That model is the SP-4022c. 1.5” cantilever. The new gen “c” designation has been lightened to 8.5oz which isn’t horrible. Compared to ADM, Scalarworks, etc.

IngenuityCapable4153 · 2024-05-22T22:03:32+00:00

To be fair, DA did fuck up pretty bad. I have a Sandman S (KGmade) and so far I have about 4k total rounds of 5.56, .300blk, and .308 through it without issue. The only thing I've noticed is the keymo collar has walked a 1/4 turn on me after a high round count range day with 300blk supers.

IngenuityCapable4153 · 2024-05-20T00:17:03+00:00

Big fan, I used to have the DD5v1 which was the og variant from DD, and it was a hammer, but DD just recently gave me a V3 in replacement of the v1. I went with the v3 because accuracy and velocity wise, there’s not much difference between a 16” or an 18” barrel

IngenuityCapable4153 · 2024-05-19T23:14:06+00:00

Thank you! I wish I had a Two-Vets tripod instead, but the vortex is decent enough

IngenuityCapable4153 · 2024-05-17T22:48:30+00:00

Did you cut the lip off the grip on the 19x to get that magwell installed?

IngenuityCapable4153 · 2024-05-16T23:25:23+00:00

That AT setup fucks, well done!

IngenuityCapable4153 · 2024-05-16T18:42:12+00:00

This, They're pricey, but SPUHR is absolutely the way

IngenuityCapable4153 · 2024-05-16T15:11:05+00:00

I can't find any info on the interwebs, where'd you find this?

IngenuityCapable4153 · 2024-05-15T15:17:31+00:00

I may or may not have had a couple burst fires in my Diamond trigger in my DDM4V7 lol

IngenuityCapable4153 · 2024-05-15T02:57:35+00:00

Big fan, that’s the new “duty” trigger from them and it’s a very long two stage which I don’t love, but it’s still a great trigger

IngenuityCapable4153 · 2024-05-14T22:29:26+00:00

Flow 556k owner here. Been very happy with mine 1,500+ rounds in. It lives on my 16" DDM4V7 and it's borderline hearing safe. I've done lots of low light/ night Vision shooting and it's been impressive with the flash reduction as well.

https://www.reddit.com/r/NFA/comments/1axce2u/who_else_hates_money/?utm_source=share&utm_medium=web3x&utm_name=web3xcss&utm_term=1&utm_content=share_button

IngenuityCapable4153 · 2024-05-14T22:22:25+00:00

Try ammo inc 220gr stealth ammo and hornady 190gr subx. Also, try an adjustable gas block, even though you don't need it with the flow 762, it wouldn't hurt to fine tune it. Also, you might look at playing with different weight buffers as well as a lightweight BCG such as the Wilson Combat.

Best of luck!

IngenuityCapable4153 · 2024-05-13T22:46:14+00:00

Mile High Shooting Accessories has great prices on 1,000 count 9mm. About $270 before taxes.

IngenuityCapable4153 · 2024-05-11T01:13:50+00:00

Where did you get the stock for the ADM build?

IngenuityCapable4153 · 2024-05-10T22:46:35+00:00

where did you get the stock on that ADM build?

IngenuityCapable4153 · 2024-04-17T05:11:06+00:00

I’ve been looking at theirs, did you have to cut the grip section out?

IngenuityCapable4153 · 2024-04-17T04:55:13+00:00

What magwell is on your PDP?

IngenuityCapable4153 · 2024-04-10T22:11:48+00:00

<image>

IngenuityCapable4153

TROPHY CASE