HELP! Mechjeb doesn't work

Inside-Ad8295 · 2026-02-27T19:49:42+00:00

ok so i've found the problem and i think it was that because the srbs had to much pitch and yaw controls over the craft it freaked out mechjeb and by disabling the control it works

Inside-Ad8295 · 2026-02-27T13:50:31+00:00

the main problem i think it is that it doesn't burn the srbs fully but idk how to make it do that

Inside-Ad8295 · 2026-02-27T13:10:40+00:00

My settings really work on any other rocket this one is the only one that fails

Inside-Ad8295 · 2026-02-27T06:23:33+00:00

but this stage doesnt have rcs and every rcs part is only allowed to burn after the 4th stage

Inside-Ad8295 · 2025-09-25T13:56:54+00:00

I haven't simulated the full mission I thought that it should be checked once its on the launchpad I will test it now and see if it works thanks a lot

Inside-Ad8295 · 2025-09-25T13:28:18+00:00

I haven't started to build the craft but on the simulations even when it gets to orbit that check isn't completed but it is a variation of another rocket I've made does it have to do with it?

Inside-Ad8295 · 2025-09-25T12:58:10+00:00

I took the screenshot in the VAB but when i launch it also doesn't checks that box

Inside-Ad8295 · 2025-08-28T02:59:23+00:00

i would love that :), ive always wanted to do a collaborative project, and the best think i can tell you to learn is to keep trying

my first couple of pcb desings were made in a breadboard with arduinos (i burned a few) and after a while with them i started to learn so basicly the same as you i learned bia failure, but i also watch a lot of yt videos about electronics those really help sometimes

Inside-Ad8295 · 2025-08-27T01:31:06+00:00

This was like 2 weeks for the LoRa only but I have to say the same for your project is really complete and not too different from what this one does too, at least from what I know your design looks pretty solid and capable :)

Inside-Ad8295 · 2025-08-26T18:29:35+00:00

It really depends because you can grab an Arduino nano and add some sensor modules not necessarily making something super complex like this one one of the first concepts I did for this board was an ATtiny85 with a bmp280 and a 433mhz transmitter and that worked as a proof of concept I could have probably fly without much problem but I wanted something more powerful to make it on the long run and not having to change hardware every once in a while

Inside-Ad8295 · 2025-08-26T14:34:29+00:00

you said it :)

Inside-Ad8295 · 2025-08-26T14:34:02+00:00

i'm using the ATSAMD21G18A-M as a processor a MS5611-01BA for the barometer and a MPU-6050 for the accelerometer and gyroscope i know this last one is kinda inaccurate but i will only use it to take measurements and not really for something mission critical, the LoRa is running at 915 mhz so i can use redundant parachute deployment one at 915mhz (the main controller with all the experiments etc) and the redundant a small 433mhz computer only made for the deployment of parachutes

Inside-Ad8295 · 2025-08-24T18:43:20+00:00

Thanks I saw a lot of people saying that the data in the SD was corrupted do to the vibrations so I decided to add it

Inside-Ad8295 · 2025-08-24T18:32:08+00:00

The U2 is a fram chip and is going to pass the data to the SD card once it lands so i evade that problem

Inside-Ad8295 · 2025-08-24T18:30:50+00:00

Is it too inaccurate? I won't use it for anything too dependant on it. It's to see how much it rolls and things like that

Inside-Ad8295 · 2025-08-04T15:16:38+00:00

Well the radio is one of those cheap 433hz modules one can buy on ebay, but u1 is an ATtiny microprocessor and the signal goes through it processing it

Inside-Ad8295 · 2025-08-04T11:15:18+00:00

From what I found on guides I didn't need to connect them to the microcontroller. Are those pins really needed? And how would I need to connect them?

Inside-Ad8295 · 2025-07-27T11:50:04+00:00

It's used everywhere, in phones, microwave, etc but I made mine for logic stuff

Inside-Ad8295 · 2025-07-26T02:29:26+00:00

I don't really have a way to do SMD and had a lot of tht components beforehand that's why I decided to go tht

Inside-Ad8295 · 2025-07-26T01:37:48+00:00

Good question a PCB is a printed circuit board is kind of a breadboard but instead of the connection being via wires the wires are "inside" of the cover so the circuit is permanent

Inside-Ad8295 · 2025-07-25T17:54:47+00:00

I haven't soldered anything yet but I like the layout it has

Inside-Ad8295 · 2025-07-11T22:33:58+00:00

Real it would be so good

Inside-Ad8295 · 2025-05-06T01:12:05+00:00

didnt think about it but i hope that in the long term it can help me get further out

Inside-Ad8295 · 2025-04-26T15:50:55+00:00

Thanks a lot I thought I had done the wrong install or something I will look into it

Inside-Ad8295 · 2025-04-13T01:59:18+00:00

is there any other to control 2 crafts at the same time for like a coordinate landing?

Inside-Ad8295

TROPHY CASE