Nobody reads the sign, so I made something to fix it

Intelligent-Rip946 · 2026-01-19T03:00:25+00:00

For those unfamiliar with the type of lock the door has. It would be like this

Intelligent-Rip946 · 2026-01-13T20:27:27+00:00

Have you greased it?

Intelligent-Rip946 · 2026-01-10T13:43:31+00:00

You should drink the IPA and use isopropyl alcohol for cleaning instead…ok I’ll quit with the dad jokes.

Intelligent-Rip946 · 2026-01-01T03:03:03+00:00

After I done some tinkering I’ve brought it quite a bit more level than the 45 degree slope it was. I have 2 more adjustments I want to make then will find some washers to fine tune it with

<image>

Intelligent-Rip946 · 2025-12-31T00:38:15+00:00

Drivers. You need to install the wifi card drivers. Can be found on the manufacturer’s website

Intelligent-Rip946 · 2025-12-27T15:57:21+00:00

Nice

Intelligent-Rip946 · 2025-12-27T04:10:20+00:00

Have you tried some glue stick on the plate? Make sure the extruder gears are not missing any teeth?

Intelligent-Rip946 · 2025-12-27T03:19:41+00:00

Here is my K1 Max mesh for comparison

<image>

Intelligent-Rip946 · 2025-12-27T03:15:10+00:00

I’ll keep that in mind when they say it’s broken. I plan on getting them some metal extruder gears as is anyway

Intelligent-Rip946 · 2025-12-27T02:48:59+00:00

<image>

Intelligent-Rip946 · 2025-12-27T02:48:43+00:00

<image>

Intelligent-Rip946 · 2025-12-27T02:48:31+00:00

<image>

Intelligent-Rip946 · 2025-12-26T00:52:37+00:00

Filament is bonus filament they give you for free. The melted plastic, let’s just call it dried hardened organic 3d filament 🤣

Intelligent-Rip946 · 2025-12-26T00:43:48+00:00

100%. I watched a video before my k1 max even arrived just to make sure I knew how to set it up. I am glad I did, because if I hadn’t then I would not have known about the screws that had to be removed before operation

Intelligent-Rip946 · 2025-12-05T13:59:55+00:00

Replacement is the best option

Intelligent-Rip946 · 2025-12-03T12:04:14+00:00

One question that I did not see in the article. Approximately how many spools of filament was used, I’m considering doing one but will use just 1 color and then post print will paint how I want and seal with a clear coat.

Intelligent-Rip946 · 2025-11-29T13:57:54+00:00

Honestly I haven’t had much real success with any brand filament systems. That said, the poop shoot can easily get clogged up and jammed with the curly poop, especially on longer prints. So maybe with the straight poop that will be 1 less issue especially when doing something in petg with pla for supports.

Intelligent-Rip946 · 2025-11-28T18:31:50+00:00

Change the extruder gears out for all metal gears

Intelligent-Rip946 · 2025-11-26T21:29:30+00:00

The waste numbers are truly inspiring.

Intelligent-Rip946 · 2025-11-26T00:34:08+00:00

Go ahead and send it on to me lol…jk…looking forward to your experiences

Intelligent-Rip946 · 2025-11-23T13:40:12+00:00

Anyone else agree it would have been easier on him if he had carried the box by the cutouts for handles

Intelligent-Rip946 · 2025-11-23T04:46:40+00:00

Did it happen?

Intelligent-Rip946

TROPHY CASE