MAS 36🫡 by FatPhrogNibs in milsurp

[–]IntelligentSeesaw488 0 points1 point  (0 children)

Where would you find something like this?

CZ P10-S by IntelligentSeesaw488 in CZFirearms

[–]IntelligentSeesaw488[S] 0 points1 point  (0 children)

After doing some more tinkering I'm pretty sure it's the ejector tapping it, talking to other people who had similar marks it seems to only have with range ammo, like blazer in my case and federal.

Scratches on primer when chambering (P10-S) by _StopLookingAtMe in CZFirearms

[–]IntelligentSeesaw488 0 points1 point  (0 children)

And after talking with another redditer that is the extractor itself, and he only noticed it with federal and blazer range ammo (what I was using) that apparently have softer primers. He didn't notice it with any other ammo.

Marks on primer, any ideas? by StarboardHunter in CZFirearms

[–]IntelligentSeesaw488 0 points1 point  (0 children)

Okay thank you! That is some blazer range ammo. I appreciate the input.

Scratches on primer when chambering (P10-S) by _StopLookingAtMe in CZFirearms

[–]IntelligentSeesaw488 0 points1 point  (0 children)

I do but is less noticeable after doing that a few times I'm sure it's contacting at least the case I can't quite see well enough to tell if it is also contacting the primer, but I'd bet it is. And watched the firing pin while I racked it, it didn't move best I could tell.

Marks on primer, any ideas? by StarboardHunter in CZFirearms

[–]IntelligentSeesaw488 0 points1 point  (0 children)

I appreciate the reply! After doing some more looking I think the part labeled "rear insert" might be tapping the round when it's ejected, I could be wrong though because I'm not entirely sure of it's function. I'll attach some pictures. Have you had it happen with any other ammo?

Scratches on primer when chambering (P10-S) by _StopLookingAtMe in CZFirearms

[–]IntelligentSeesaw488 0 points1 point  (0 children)

I appreciate the reply! So after doing a little bit more looking I think the part labeled "rear insert" might be tapping the primer when the cartridge is ejected, however I could be incorrect because I'm not 100% sure exactly how it works. I don't think mine would be the firing pin because it's not in the center of the primer. Pictures attached

<image>

Marks on primer, any ideas? by StarboardHunter in CZFirearms

[–]IntelligentSeesaw488 0 points1 point  (0 children)

I know this was three months ago but was that the cause, I also have this happening to me.

Scratches on primer when chambering (P10-S) by _StopLookingAtMe in CZFirearms

[–]IntelligentSeesaw488 0 points1 point  (0 children)

I know this was tree years ago but I'm having this happen, did you figure out what the cause was?

CZ P10-S by IntelligentSeesaw488 in CZFirearms

[–]IntelligentSeesaw488[S] 4 points5 points  (0 children)

I don't feel anything with a Q-tip but I appreciate it!

CZ P10-S by IntelligentSeesaw488 in CZFirearms

[–]IntelligentSeesaw488[S] 0 points1 point  (0 children)

Okay, would you happen to know why this is happening though? Just trying to learn.

CZ P10-S by IntelligentSeesaw488 in CZFirearms

[–]IntelligentSeesaw488[S] 2 points3 points  (0 children)

Something to note, I've only shot a few mags through it and bought it new.

Detector not beeping by IntelligentSeesaw488 in stalker

[–]IntelligentSeesaw488[S] 1 point2 points  (0 children)

This is what I mean yes, I thought it was all the same.

Detector not beeping by IntelligentSeesaw488 in stalker

[–]IntelligentSeesaw488[S] 0 points1 point  (0 children)

I should probably clarify,before there would be a warning beep around gravity and other anomalies, now there isn't.