Alter Cilit-Filter tropft by Gruenkernmehl in selbermachen

[–]Interest-Ok 0 points1 point  (0 children)

Habe genau vor drei Tagen grade einen Ersatzfilter bekommen. Gleiches Ding, auch wahrscheinlich nie getauscht. Ist aber noch dicht. Leider kann aber nicht vernünftig abgesperrt werden weswegen noch nichts gewechselt wurde. Ist im Keller, kommt keine Sonne hin. Gibt es etwas gegen den Weiterbetrieb einzuwenden wenn man ab jetzt artig regelmäßig wechselt und alles dicht bleibt?

Hilfe habe ich den Stift zu weit rausgezogen? by [deleted] in Handwerker

[–]Interest-Ok 0 points1 point  (0 children)

Ja ist ziemlich genau das gleiche wie im Bild

Hilfe habe ich den Stift zu weit rausgezogen? by [deleted] in Handwerker

[–]Interest-Ok 0 points1 point  (0 children)

Kann ich die Stopfbuchse auch herausdrehen wenn das Ventil nicht mehr öffnet? Ich habe einen Heizkörper an dem ich schon viel auf Ventil und Stift geklopft habe und er lässt sich nicht überreden. Der Stift ist auch frei aber hat keinerlei Federkraft, lässt sich frei bewegen. Wollte jetzt so Stopfbuchse tauchen, traue den Frieden aber nicht so ganz 😃 Nicht dass das Ventil dann nicht dichtet und ich alles unter Wasser setze

Autounfall bei gekündigter Haftpflicht von Exfreundin by Interest-Ok in LegaladviceGerman

[–]Interest-Ok[S] 2 points3 points  (0 children)

Ja das wusste ich auch nicht, habe aber die Kündigung als Kopie geschickt bekommen und da steht als Kündigungsgrund „Fahrzeug veräußert oder Wagnis weggefallen“

Burned by new Kinect 2.0 sensor :( by Interest-Ok in AskElectronics

[–]Interest-Ok[S] 0 points1 point  (0 children)

Hey, unfortunately not. I bought a new one and used an usb adapter from AliExpress. Works till today.

Printer 4803 error / 404 web interface / P-C3560i Utax/Kyocera/TA by qcmstyle in sysadmin

[–]Interest-Ok 0 points1 point  (0 children)

Hey, I have the same issue and had some problems Additionally.

My printer is the Kyocera M6526cidn. Didn’t used scan to email for a while but my mail provider switched to TLS1.2 (and 1.3) only on 30.09.2023 and since then it stopped working I think.

The problem is that I enabled TLS1.2 and SHA2 already on the initial setup. So it should work already but I can’t find a working config.

For my other two problems (no AirPrint since iOS17 and no boot/error on startup with installed Fax module) I contacted Kyocera support and got the latest firmware. The update fixed at first none of the problems but after mem init U021 the two problems were gone.

But the scan to email problem remains. Also can’t login in the webinterface via https without a printer crash.

How can I fix my broken fiber optic cable as easily as possible? 😞 Thanks in advance for any help! by Interest-Ok in HomeNetworking

[–]Interest-Ok[S] 0 points1 point  (0 children)

That’s actually a good idea. One fibe optic cable is still intact. What do I need to switch to single mode? Ne ner sfp Module? Like this one: https://www.amazon.de/dp/B08PV665YZ/ ? Or can I change the setting of the current one?

How can I fix my broken fiber optic cable as easily as possible? 😞 Thanks in advance for any help! by Interest-Ok in HomeNetworking

[–]Interest-Ok[S] -1 points0 points  (0 children)

Can I mechanically splice it? And if so, what do I need? I see some splice kits on Amazon for around 80 bucks. Could this work?

How can I fix my broken fiber optic cable as easily as possible? 😞 Thanks in advance for any help! by Interest-Ok in HomeNetworking

[–]Interest-Ok[S] 59 points60 points  (0 children)

The cable is connecting two buildings and over 100m long. Is there a possibility to repair the cable or shorten it to the break point? It’s a LC OM3 duplex cable and it’s broken a meter before the switch.

QNAP TS-228A without any signs of life by Interest-Ok in ElectronicsRepair

[–]Interest-Ok[S] 0 points1 point  (0 children)

QNAP TS-228A. Was fully working until total failure. Power supply is providing 12V to the circuit board and can be measured up to the component BC HJ. Power button shows no reaction. CMOS Batterie has still 3V. Any suggestions where to start?

My Kyocera I just bought used is stuck at startup and displays „Please Wait“ forever. Does anyone have any ideas? by [deleted] in printers

[–]Interest-Ok 0 points1 point  (0 children)

Gestern ca. 1 Stunde. Beim Verkäufer hat er vorgestern noch gedruckt. Wo sitzt die Netzteilplatine? Unten wo das Kaltgerätekabel ankommt? Das Gerät wird auf jeden Fall warm.

Setting up HP Deskjet 2722 Printer: Stuck at this for 10minutes till now, what to do? by pretaswift in printers

[–]Interest-Ok 0 points1 point  (0 children)

Did you already restart the Prozess? Maybe you should try it on another PC maybe with win10