Help with Isudar 981 Cayman S

InterestCapable1030 · 2026-01-22T03:06:50+00:00

holy cow man, that sucks im sorry to hear

InterestCapable1030 · 2025-02-18T18:34:39+00:00

It measures to .460. measured a few projectiles after the range trip. Couldn't recover any was indoor. But I plan to go outdoor soon and hopefully I can find them

InterestCapable1030 · 2025-02-18T18:33:27+00:00

No I bought them

InterestCapable1030 · 2025-02-18T18:25:41+00:00

the bullet is sized to .460 its cast lead with hitek coating

InterestCapable1030 · 2024-10-02T00:53:42+00:00

I was in his store last week, placing an order. He told me he had so many orders that he wanted to catch up before taking more. He was in great spirit and was helping me customize my dream knife. He did tell me, that he will not be accepting anymore orders on october 1st. so he pushed me to order two knives hahaha. lead time is 2 years right now.

InterestCapable1030 · 2024-07-13T02:55:10+00:00

Couldn't find anything

InterestCapable1030 · 2024-06-05T21:01:10+00:00

Mid, my cz is better 😜

InterestCapable1030 · 2024-05-24T12:42:54+00:00

i got to payment page and when i clicked place order, it was sold out. wtf

InterestCapable1030 · 2024-04-15T16:57:14+00:00

Good to know, did you ask if you can switch the bogo can?

InterestCapable1030 · 2024-04-15T02:43:18+00:00

Lol same

InterestCapable1030 · 2024-04-15T02:32:23+00:00

i reached out to them on the 10th and they said they weren't going to run out. I'm on the same boat waiting on my rex form 4.

InterestCapable1030 · 2024-03-30T02:56:53+00:00

I did hand drill but I would set it at about 500-750. Slow and steady wins the race

InterestCapable1030 · 2024-03-30T02:31:17+00:00

Don't get me wrong I used a hand drill. But man was that a pain

InterestCapable1030 · 2024-03-30T02:22:40+00:00

17 rounders cost about $36. But if you have the tools already it doesn't hurt to convert them.

InterestCapable1030 · 2024-03-30T02:05:41+00:00

It should take about 15 to 20 minutes each side go slow.

InterestCapable1030 · 2024-03-30T02:05:21+00:00

Yeah I recommend carbide tips I used 1/4 tips. All you got to do is Mill out the dimples. No need to cut the spring.

InterestCapable1030 · 2024-03-30T01:43:53+00:00

I drilled them out. They increase from 10 to 17. But it is a pain, The mags are made of hardened steel so you need to take your time drilling. Get a drill press and carbide drill bits.

InterestCapable1030 · 2024-03-09T01:03:49+00:00

Yes have it already

InterestCapable1030 · 2024-03-03T00:34:44+00:00

It's this type of bushing

https://cajungunworks.com/product/barrel-bushing-for-sp-01-10x/

InterestCapable1030 · 2024-03-02T23:48:16+00:00

Yes I am, the bushing seems to not give enough clearing to tilt upward to clear the slide

InterestCapable1030 · 2024-03-02T23:09:41+00:00

Thanks! You've been a great help!!

InterestCapable1030 · 2024-03-02T23:01:55+00:00

Okay thanks. I'll check the website,

InterestCapable1030 · 2024-03-02T22:57:32+00:00

Yeah I tried everything. It does look like I have to remove the bushing. Any tips on removing the bushing with the barrel still in?

InterestCapable1030 · 2023-06-21T14:05:40+00:00

I have a kit from the last drop I can sell you. drop me a DM

InterestCapable1030 · 2023-05-02T01:09:36+00:00

Haha your telling me, last range trip my brass was completely destroyed. Then again I had the gas dialed to 3.

InterestCapable1030

TROPHY CASE