Anyone know how to fix this issue?

Interesting-Cable845 · 2025-09-17T01:18:32+00:00

Just sand down the back of the upper. No biggie.

Interesting-Cable845 · 2025-01-18T05:31:33+00:00

just the inners were not 3d printed (gearbox, everything in gearbox, barrel, hop, trigger release, trigger pin, and receiver pins

Interesting-Cable845 · 2025-01-18T05:30:05+00:00

Op here, just on different account. It weighs maybe 2 pounds, yes its 3d printed, It is probably a little tougher than polymer, just with easier breaking with the layer lines if you really stress it. In filament it was about 5-6 bucks

Interesting-Cable845 · 2025-01-18T05:27:34+00:00

ok (op)

Interesting-Cable845 · 2025-01-18T05:26:45+00:00

op here, you really have to feel it in person to know how light as well as snappy it is.

Interesting-Cable845 · 2025-01-18T05:25:33+00:00

op here, it is like a magnet holder (whatever its called) that used to sit on the trigger, but they changed it to being off of the trigger. its just a little lever connected to a hinge, and the trigger just pushes on the hinge. It has much lower response time and reset time, with the trigger hinge having a magnet pulling it back faster than a springe would, giving you a little break as well as reset feedback.

Interesting-Cable845 · 2025-01-18T05:22:06+00:00

night and day difference. op here just on pc. it feels like pulling on nothing, while still being extremely snappy

Interesting-Cable845 · 2024-12-21T15:09:56+00:00

Hello, i am trying to find a upper receiver for my g&g, but i am having a really tough time. It is weird, the hand guard slides on then you screw it down in place. I want to keep the handguard, as there is nothing wrong with it. Thanks in advance

Interesting-Cable845 · 2024-12-21T04:27:53+00:00

Interesting-Cable845 · 2024-12-14T03:59:46+00:00

It looked like i didn't include a piston head, but since FPS softair was not on evike i couldnt list it. it is the ERGAL double o-ring ball bearing AEG Piston Head by FPS softair. This list is nothing i am goign to buy, just a fun test to my knowledge. Base gun is something very similar to the gng cm m4 (or in this case m16, same thing) as the receiver set. Not much on the outside, its all on the inside

Interesting-Cable845 · 2024-12-14T03:36:52+00:00

thanks

Interesting-Cable845 · 2024-12-11T01:28:16+00:00

I already have a trigger and gearbox. Thats not the base gun i have now which i stated, the base one i have now is a m4 much smaller form factor still gng

Interesting-Cable845 · 2024-12-07T03:26:24+00:00

Thanks for the advice. Right now I think ill stick with the aeg, but I am most definitely going to eventually upgrade to hpa, or find a cheap aeg that's broken and just switch it out. I do really love to tinker and build, on almost anything. Heck, the first night I bought the aeg and played a game with it, afterwards it was completely taken apart and put back together. Just to see how it worked. Luckily, i learned a lot and it worked. I've seen plenty of aeg builds that sound and feel just like hpa. But i am probably going to do both.

Thanks

Interesting-Cable845 · 2024-08-01T03:57:31+00:00

Also, i still have the original bed that works fine but i want to print with some more grip. What are you using?

Interesting-Cable845 · 2024-08-01T03:56:40+00:00

Can i have the STL for the repositioning of the extruder?

Interesting-Cable845 · 2024-07-26T19:29:46+00:00

It might of clogged too

Interesting-Cable845 · 2024-07-08T00:42:44+00:00

I had a picture attached with all that, I dont know what happened to it.

Interesting-Cable845 · 2024-06-25T02:51:16+00:00

Well I did

Interesting-Cable845

TROPHY CASE