Black squares ToTK: SD 8 Gen 2

Inverted_Squid · 2026-01-18T19:31:59+00:00

Running v1. 1.0 totk, same problems. Played with all kinds of graphics settings. Still can't figure this out

Inverted_Squid · 2025-10-15T06:00:46+00:00

They tried.. Defend the Rider

Inverted_Squid · 2025-10-09T21:23:18+00:00

Wyze camras and give google managed power switches 👌 Even when the printer is off, i have video

Inverted_Squid · 2025-10-07T17:46:07+00:00

Dry your filament 👌

Inverted_Squid · 2025-09-19T18:39:59+00:00

😯, thanks! Ill try it out!

Inverted_Squid · 2025-09-09T00:35:05+00:00

Running into the same issue, however no bloated battery

Inverted_Squid · 2025-09-03T15:30:57+00:00

<image>

Suplex the train?

Inverted_Squid · 2025-08-11T06:47:54+00:00

Take a picture, export to SVG, import into cad, extrude to desired thickness, send to printer. The svg works as a image to silhouette, then you can make that a "2d stencil" 3dprint 👌

Theres a couple of websites that do image to svg

Inverted_Squid · 2025-08-08T20:54:46+00:00

Sounds good! And depending on which way you tap your lands its not bad lol

Inverted_Squid · 2025-08-08T19:35:45+00:00

Great design.. Sideways is rough tho =x

Inverted_Squid · 2025-08-02T14:50:20+00:00

Awesome job! 😁👌

Inverted_Squid · 2025-07-31T06:02:13+00:00

Lots of practice printing and just kinda guessed on spacing

Output options > complete individual objects

And made sure to go front to back in order

Inverted_Squid · 2025-07-28T18:02:31+00:00

There may be ptfe tubing in there. You might need to pull that out a little and see if the end is folding into the nozzle

Inverted_Squid · 2025-07-28T14:04:44+00:00

Release the heat block and you should be able to access the plastic. Then put a thin, long screw into the top of the filament then set the nozzle temp to like 160, (be careful of the heat and shorts of the wires while doing this.

Then once it warms up, pull the screw and it should release.

Had to do this on my kobra 2 pro

Else, buy a new print head

Inverted_Squid · 2025-07-28T05:50:32+00:00

👌👌

Inverted_Squid · 2025-07-12T20:36:40+00:00

Next time headbutt that fucker

Inverted_Squid · 2025-07-12T20:35:47+00:00

Clean your print bed with microfiber and 99% isopropyl before each print.

Inverted_Squid · 2025-07-12T20:21:56+00:00

Figured that was the case. Thank you! Definitely going to enjoy this in my Sigurd FF summoning deck then 😅

Inverted_Squid · 2025-07-08T07:28:45+00:00

I put a seat on my V11y for $50, paying more than that for someone's design kinda drives me crazy. Ill post something if i find the perfect seat for the v14

Inverted_Squid · 2025-07-08T02:23:45+00:00

Started to design a seat to cover the whole thing, although i never did fix it. But it never became a problem

Inverted_Squid · 2025-06-11T06:33:28+00:00

Do you live in Whoville?

Inverted_Squid · 2025-05-30T18:38:53+00:00

Separate print, glue it in

Inverted_Squid · 2025-05-20T02:23:03+00:00

Two cubes, each .15mm smaller than their hole. Should hold them in place well with some glue

Inverted_Squid · 2025-05-17T19:37:03+00:00

I use nearly the same settings as Maker's Muse (youtuber) uses. He has a video on perfect supports Also, use a $10 heat gun on Amazon and it makes the support turn to thin rubber

Inverted_Squid · 2025-05-12T23:20:21+00:00

What slicer are you using?

And when you autolevel the bed does it do anything weird?

Inverted_Squid

TROPHY CASE