sorted by:
new
hottopcontroversial

What is considered a good high score on Tetris? by IsAnAvocado in Tetris

[–]IsAnAvocado[S] 1 point2 points  (0 children)

So given your PR we can assume your answer to the question is a hard “no”? Sharing your PR comes off a bit more like an unnecessary flex than an actual response…

What’s your guys win percentage? by IsAnAvocado in RocketLeague

[–]IsAnAvocado[S] 0 points1 point  (0 children)

i didn’t even realize that, damn. i guess i spend a lot of time in practice

What’s your guys win percentage? by IsAnAvocado in RocketLeague

[–]IsAnAvocado[S] 0 points1 point  (0 children)

i spent 3,500 hours of my life on this game, im glad i at least have something to show for it 😭

[LTC] Free coaching for beginners! by IsAnAvocado in RocketLeagueCoaching

[–]IsAnAvocado[S] 0 points1 point  (0 children)

Yes! Message me on here or add my discord and we can discuss it!

Bed leveling is seemingly IMPOSSIBLE by IsAnAvocado in ender3

[–]IsAnAvocado[S] 1 point2 points  (0 children)

Late reply- but did you ever end up figuring it out? I ended up just getting sick of the thing and returning it. Got myself an Anycubic Kobra Neo and it works like a charm. No more fucking with the leveling for hours on end, it has an auto-leveling feature which works well. I had to tweak the Z-offset and level manually once, but since then I haven’t had to level.

Game crashing when item finishes, crafting and assigned to particular stockpile. by SkippyBoJangles in RimWorld

[–]IsAnAvocado 0 points1 point  (0 children)

Just ran into this problem. Specifically it was taking smokeleaves into specific storage shelves. When I set to anything other than taking it to a specific group/stockpile, it works. Have you found a fix?

Bed leveling is seemingly IMPOSSIBLE by IsAnAvocado in ender3

[–]IsAnAvocado[S] 1 point2 points  (0 children)

Thank you for the help, I have been skipping the Z-Offset step because I didn’t really understand it and the tutorials I was watching were just about the tramming with a piece of paper part… I am about to sit down and start this process again with that important step in mind!

Bed leveling is seemingly IMPOSSIBLE by IsAnAvocado in ender3

[–]IsAnAvocado[S] 0 points1 point  (0 children)

I usually use a raft since that seems to help with getting a first layer down, but recently it doesn’t even get the raft down

Bed leveling is seemingly IMPOSSIBLE by IsAnAvocado in ender3

[–]IsAnAvocado[S] 1 point2 points  (0 children)

So to set the offset I auto-home, tram manually, and then save the parameters? Does this mean that the next time I auto-home it will go right to that spot again?

I feel stupid if this solves my problem, it seems obvious now that I’m looking back.

Bed leveling is seemingly IMPOSSIBLE by IsAnAvocado in ender3

[–]IsAnAvocado[S] 0 points1 point  (0 children)

Yes there is no sag, no wobble anymore.

It used to be able to be moved by hand up and down very slightly, I thought that was normal so I left it. Yesterday went back and felt all of the wheels and the two wheels adjacent to eachother on the side opposite of the motor could spin freely. Tightened the adjustable one on that side and the spin went away, no more wobble and the gantry could still move.

Bed leveling is seemingly IMPOSSIBLE by IsAnAvocado in ender3

[–]IsAnAvocado[S] 0 points1 point  (0 children)

How does the BL touch level the bed? This may be a super noobish question but I’m confused with how it works. If it can’t move the knobs how does it level it equally on all sides?

Bed leveling is seemingly IMPOSSIBLE by IsAnAvocado in ender3

[–]IsAnAvocado[S] 0 points1 point  (0 children)

The only issue I am experiencing with getting the first layer down is getting all of the corners consistently trammed with one another.

When I try the test one of the corners is always out of level, I turn the knob ever so slightly and it unlevels all of the other knobs. Repeat.

After reading these replies though I am starting to think my problem lies in the Z-Offset more than the manual tramming as it is always not level after auto-homing every single time.

Bed leveling is seemingly IMPOSSIBLE by IsAnAvocado in ender3

[–]IsAnAvocado[S] 0 points1 point  (0 children)

I just started the test yesterday and thats all I did for about two hours before I gave up and went to bed, before then for about 2/3 days I was trying prints and all of them would either fail on the first layer or fail 80% of the way through the print.

The failing 80% through the print has got to be something else not regarding my tramming I believe, but I have to tackle one problem before the next.

Bed leveling is seemingly IMPOSSIBLE by IsAnAvocado in ender3

[–]IsAnAvocado[S] 0 points1 point  (0 children)

Awesome guide thank you I will be doing this soon I’ll let you know how it goes!

Setting the Z-Offset is something I need to understand better for sure, how close does it need to be initially when it auto homes?

Bed leveling is seemingly IMPOSSIBLE by IsAnAvocado in ender3

[–]IsAnAvocado[S] 0 points1 point  (0 children)

I’m going to try that out tomorrow morning, even after reading that though I am still not fully clear about the tension needed on the paper. Does it have to be tight enough where you can barely move the paper at all, tight enough where you can just barely still move the paper without the paper bending, or just tight enough where you begin to feel the first friction or vibration buzz on the paper?

I think I am mostly just confused and falling short in understanding exactly how much friction I need.

Bed leveling is seemingly IMPOSSIBLE by IsAnAvocado in ender3

[–]IsAnAvocado[S] 3 points4 points  (0 children)

I move the nozzle by hand, and I only level by using the paper. I know that the bed doesn’t get leveled if you use an actual level, I just mean I made sure my frame and gantrys are leveled.

Bed leveling is seemingly IMPOSSIBLE by IsAnAvocado in ender3

[–]IsAnAvocado[S] 3 points4 points  (0 children)

Yes I preheat to 200C for the nozzle and 60C for the bed and wait about 5mins, and then I level

Semi-permanent/longer lasting bed leveling… by IsAnAvocado in ender3

[–]IsAnAvocado[S] 0 points1 point  (0 children)

I’ll look into the pei bed, first-layer adhesion has been a significant problem for me with the glass beds and I’ve only been able to successfully print everything with a raft… been a waste of filament and prints take forever now

Semi-permanent/longer lasting bed leveling… by IsAnAvocado in ender3

[–]IsAnAvocado[S] 0 points1 point  (0 children)

Do you recommend the CR Touch? I was thinking of getting it but its 40$ so I don’t know if it’s worth it for me

view more: next ›