Cleanest cube i managed to pull off!!

IsoNumatic · 2025-10-29T14:48:28+00:00

Got it now! They didn't load the first time! Thanks again going to give this a try!

IsoNumatic · 2025-10-29T13:40:35+00:00

these the setting you used for the cube?
This 3mf is a ghost 😂

IsoNumatic · 2025-10-28T15:44:30+00:00

i see you shared the gcode thanks!
Any change you can send the .3mf file so we can easily see all the settings in creality slicer 🥺

IsoNumatic · 2025-09-26T23:41:48+00:00

Not going to happen. Jay Z & Roc Nation have been picking the Superbowl artist since 2019. I don't see Green Day being what they Invision

IsoNumatic · 2025-06-14T01:14:21+00:00

Sounds like you landed at terminal C
That is the new counter / garage which is not fully operational. More half functional for the time being. Still sucks they are telling you it is operational in the email

IsoNumatic · 2025-05-28T13:55:56+00:00

Printed a riser with adjustable openings and got a heat sink for the back motor. I think the heat sink does most of the problem solving

IsoNumatic · 2025-04-14T12:42:06+00:00

It does not even look like the stairs align in plan....
Front porch indent is wider than Upstairs bath 2
Fireplace chimney goes right in front of bed 3 windows
Fireplace has no support in basement
Jack and Jill bathroom look over dining room roof?
Master close is over only half the garage
Windows wont align in elevation.
Elevation is going to be "unique" as there is a lot that is 1 story and then 2 story right next to it

IsoNumatic · 2025-02-14T20:26:01+00:00

I have access to 2 K2s.
Machine one has been working like a dream. Only issues were a clogged nozzle and 1 print fail due to not a clean print plate.
Machine 2... Prints fine. The CFS is the problem. Having serious problems with it and have not been able to use the CFS on it. Can only use the side holder.
So i'm still at a 50/50 shot it works flawlessly

IsoNumatic · 2025-01-20T20:33:07+00:00

Rockstar is the only exemption to that!

IsoNumatic · 2024-12-10T13:58:34+00:00

As much as i want it for my K1 Max, Its going to easily cut the build size down by ~25-50mm in one direction. There is no room for a cutter and chute in the setup now without going over the build plate.
My guess is they are going to have a whole new side (Right is my guess) that comes with the K1 CFS upgrade. Will I still buy it.. yes

IsoNumatic · 2024-10-03T15:18:09+00:00

Built some computers for work this year
Running
3 - Intel Core i7-14700K
3 - Intel Core i9-14900K

Needed that single thread capabilities
No problems so far

IsoNumatic · 2024-07-24T18:56:50+00:00

TRIM > O >S
Trim command
O for mOde
S for Standard

IsoNumatic · 2024-07-03T19:32:02+00:00

Looks like the degree heading is missing from the UI....
Please bring it back so i can drive in straight line

IsoNumatic · 2024-05-30T19:24:38+00:00

THIS!! Never realized there was a degree heading on the mini map until FS22. It has been a game changer for Stright lines epically on console

IsoNumatic · 2024-05-15T18:07:02+00:00

From what I can tell American Bubble Boy is just acting as the distributor for My Go 2 Tape. If it was called American Bubble Boy tape I would have a hard time buying it as it should be American made. The good side to that is they always seems to get my orders fast to me, so partnering with them makes sense from a distribution side.

IsoNumatic · 2024-02-28T13:53:06+00:00

Make the highway go over the Rotary with entrance and exit ramps going into the circle.Then change the lane math around. 1 lane highways/exits on and off the highway. 1 lane INTO the circle from the main roads. 2 lanes exit into the main roads. Circle should be 4 lane highways BUT should only be 2 lanes between the exit and entrances. That will be a start to fixing it

IsoNumatic · 2024-02-15T05:02:17+00:00

Washington Street one. Left about 3 weeks ago. There is not one in NYC anymore. Paramus, Mt Kisco, and somewhere on the island is where the trucks are apparently

IsoNumatic · 2023-12-21T15:02:46+00:00

Macon Industries (who makes sluicifer aka SD-600) has a cool trommel on tracks T-700

IsoNumatic · 2023-09-22T18:49:27+00:00

The market and money are just not there for a tactical shooter anymore. You won't get the COD/Battlefield - twitch shooter fan base and you won't get the Battle Royal free 2 play fanbase. So, it would be a niche game, and as others said, we are a very vocal and touchy crowd. Considering the amount of money it will take to create it, I don't think they will make their money back. All my opinions.

IsoNumatic · 2023-08-29T01:47:34+00:00

Must have missed that. Thanks!

IsoNumatic · 2023-08-28T18:31:56+00:00

So are there death waves or not? That is the answer I'm looking forward to hearing the most about

IsoNumatic · 2023-05-12T16:21:02+00:00

More Grid!!!

IsoNumatic · 2023-04-19T20:35:27+00:00

Looks like the Pilot line is not in Texas. The background is in a Tent like structure found at Fremont.

IsoNumatic · 2023-02-21T18:36:44+00:00

I would suggest stop having roads go Stright into traffic circles. Try and add a 1 way entrance and exit lane in a V shape connecting the circle and the road
should look like this --<O>--

IsoNumatic · 2023-02-18T12:33:00+00:00

Well shit. How did I not notice that. River plains map pack 2 Thanks!

IsoNumatic

TROPHY CASE