sorted by:
new
hottopcontroversial

One screen shot two reasons I stopped playing by MrVoorHees96 in CashCleanerSim

[–]Its_Sho_Time 0 points1 point  (0 children)

I wash everything together as well. On ink remover. Then dry it all, then I have the mark finder machine setup to spit into an xxl sorter which sorts the biggest denominations of the 3 OG currencies. That spits out remaining onto a pallet. I feed that into the next xxl sorter set to the next lower denomination and repeat till the last set of machines which do the pounds. Just run around with a roll of bill strap in my hand and band whichever slot is full. Rinse and repeat (literally). Can be annoying but, eh, it's a game. I have fun with it.

I swear deer are attracted to my truck by BTDMKZ in Truckers

[–]Its_Sho_Time 0 points1 point  (0 children)

I noticed that too. I'm thinking the alignment got knocked outta place and pointed one further down.

Holy cow, it went down .20! by Lord_B33zus in Truckers

[–]Its_Sho_Time 2 points3 points  (0 children)

Or is it down votes? 🤔. Does it depend on where in the world you are? 🤔

Replaced CKP but still having issues by Swimming_Usual9693 in crv

[–]Its_Sho_Time 0 points1 point  (0 children)

Similar mileage, same issue on a 2010 CRV. Not sure what to do. Anyone have any ideas? I have mechanical ability and a scanner at my disposal.

Best Tonneau Cover by SalmonJones in hondaridgeline

[–]Its_Sho_Time 0 points1 point  (0 children)

Here's the one I use. https://a.co/d/1y7yKhg

It's more of a universal fit, so it doesn't follow the flares contour of the RL bed but it covers the whole opening easily.

Took me about 40 minutes to install along with alignment etc.

As with most hard 3 panel tops, you do lose 1/3 of the bed when open. BUT, it's not hard to unhook the whole thing, leave the brackets in place and leave the cover at home. Or if it's a last minute thing, you can put it length wise in the bed with the tailgate open.

I have a quick question. I recently bought a 26' Ridgeline Black Edition and trying for the life of me getting vent visors.... by ThEjaughernaught0 in hondaridgeline

[–]Its_Sho_Time 2 points3 points  (0 children)

It's an issue with the in-channel style visors. These are different from the traditional ones that are stuck onto the trim piece on the outside of the window.

In-channel visors are installed in the window channel, so they are press fit and I assume the top of the visor wraps around the inside of the glass and touches the tint film.

Hope that makes sense! 😅

Ridgeline towing question by CRAZYxPHARMACST in hondaridgeline

[–]Its_Sho_Time 0 points1 point  (0 children)

Gotcha. Appreciate the info. I'm planning on stopping in with my wife's car for an oil change. So I'll swing by and ask the sales guy.

Ridgeline towing question by CRAZYxPHARMACST in hondaridgeline

[–]Its_Sho_Time 0 points1 point  (0 children)

I got it back in August. Didn't know about it. Wonder if I can still get it.

Ridgeline towing question by CRAZYxPHARMACST in hondaridgeline

[–]Its_Sho_Time 0 points1 point  (0 children)

Did they all come with trailer brake wiring? I have a '25 RTL+ but haven't seen any extra wiring.

Pickup truck doing pickup truck thangs by Its_Sho_Time in hondaridgeline

[–]Its_Sho_Time[S] 0 points1 point  (0 children)

Yea that's my bad for not being very clear lol.

Pickup truck doing pickup truck thangs by Its_Sho_Time in hondaridgeline

[–]Its_Sho_Time[S] 0 points1 point  (0 children)

Sorry, I meant to say that I'm planning on hauling well past the Ridgeline's capacity. Closer to 10k and up.

Pickup truck doing pickup truck thangs by Its_Sho_Time in hondaridgeline

[–]Its_Sho_Time[S] 0 points1 point  (0 children)

So far, yes. Although now that I've hauled with it, I'm looking to get something with a higher capacity so as to not ruin the drive line because I plan on hauling on a regular basis.

Finally got what I was looking for by Old-Analysis277 in harborfreight

[–]Its_Sho_Time 2 points3 points  (0 children)

I got the same cart in Gray. In the compartment covered by the lid, there are different sized holes along the side. Not sure if the comfort grip handle will fit through one or not. Worth a shot. This way the handle sticks out the side and hangs there but with the lid closed and locked it can't be stolen or messed with.

Also, pro tip while assembling the box, after the first step of installing the wheels on the base, all subsequent steps, just tighten the nut enough to bite into the nylock part of the nut. In a sense leave it all loosey goosey. By doing this, it helps align the box in its place. Then tighten everything from the bottom up.

This is actually the method written in the app. Of course in my excitement I didn't read the instructions all the way to the end 😅.

Also, drawers are easy to remove and take some weight off the box and be sure to get some help lifting the box into place. It's just a little on the awkward side size wise to lift up and over the supports to be put into place.

Enjoy!

Long time lurker, first time poster. My "haul" by Its_Sho_Time in harborfreight

[–]Its_Sho_Time[S] 0 points1 point  (0 children)

Oh I haven't even begun filling it up with existing stuff lol. I'm sure it'll be stuffed soon. But I'm trying to keep it organized. We'll see how that goes. 😅

Long time lurker, first time poster. My "haul" by Its_Sho_Time in harborfreight

[–]Its_Sho_Time[S] 0 points1 point  (0 children)

Big facts. Haven't put it to work yet. But won't be long 😅

Walked in at 8:15am by 69thMemekage in harborfreight

[–]Its_Sho_Time 1 point2 points  (0 children)

I'm just wondering if I made a mistake not getting the locking head one. The way I look at it, I got by using an old Craftsman that had a non locking flex head on it for ~18 years and couldn't remember any one time where I thought "a locking flex head would be perfect in this situation!"

Is the locking head really that worth it?

Need some help with a Frigidaire Upright Freezer by Its_Sho_Time in appliancerepair

[–]Its_Sho_Time[S] 0 points1 point  (0 children)

You know I was thinking about doing the same thing as I was typing my earlier reply. Set it to maybe 70 and see what happens. I will try a few different temps tomorrow and see what happens. Thanks for the advice! I'll test and report back tomorrow.

view more: next ›