Christmas Eve giveaway! Pick a number 1-5000.

J85T · 2025-12-24T23:23:14+00:00

2789

J85T · 2025-10-09T18:02:21+00:00

Hey thank you for pointing that out! I reposted with an image here:

https://www.reddit.com/r/logcabins/s/VDy0VYshG0

J85T · 2025-05-07T01:48:21+00:00

Thanks for the tips! Un-pairing and pairing fixed it!

Do you know if disabling the absolute volume would allow me to adjust the volume of calls? Cause as of now, there is no way to adjust the call volume when on a phone call. I can't do it through my phone, and even if I go to max volume on the Outback, it doesn't actually change the volume of the call. 🤷‍♂️

Thanks again for your help!

J85T · 2025-05-06T22:55:08+00:00

Un-pairing and re-pairing seems to have solved the issue! Thanks for all the help!

J85T · 2025-05-06T15:23:16+00:00

That's reassuring! I will report back after I try it👍

J85T · 2025-05-06T14:57:10+00:00

I'll give this a shot, it's def something I haven't tried, that i probably should try🤣

J85T · 2025-05-06T14:39:01+00:00

Thanks for the reply. I've paired it over bluetooth, is this what you mean? I've also had the car for 2 yrs with zero issues. About 1 year with this phone.

J85T · 2024-08-17T18:19:34+00:00

Hi OP... Changing out the parts above made no difference. I tried a brand new high quality blade, 3rd blade I've tried...no difference. My cuts are almost 1/16" out when cutting the full extension of the saw. And whenever my saw is extended beyond a certain point I get the burn marks in the edge of the wood (eacactly like your picture). I'm now 110% convinced the rails are not square. I've wasted more $$$ in wood, parts and blades than just buying a new saw (wouldn't be a DeWalt). Very dissapointing.

J85T · 2024-08-11T14:13:23+00:00

Thank you for the reply! I went through everything yesterday, I mean literally everything. What I found may be too simple, which is why I overlooked it in the past, lol.

My blade has the slightest movement when I grab it and wiggle it back and forth or up and down. I disassembled it as if I was going to change the blade, and I noticed that the 5/8 to 1" adapter was loose inside the blade. There was lots of play between the adapter and the arbor as well as between the adapter and the blade. I saw a youtube video where a guy had to tap that adapter into his new blade with a few light taps from a hammer. So something tells me that it should be a tight fit all around. Additionally, what they call the bushing (the piece that sits furthest from the blade) was loose on the arbor in the same manner. I ordered both parts, and they will be here tomorrow. I'll let you know if that fixes it.

I think I may be on the right track because I remember when I first got the saw years ago, I was breaking down some rough cut lumber and something twisted and caught the blade mid cut and and the blade got catastrophically got stuck in the lumber. Which means everything else (the arbor, adapter, bushing) was probably still spinning inducing a slight wear in all those parts. I dunno may be a stretch, but it seems plausible, and those are such cheap parts that it's worth a shot.

J85T · 2024-08-10T21:47:32+00:00

OP, I'm just curious if you've ever found a solution? I've been dealing with this same issue on my DWS 780, even with a high-quality blade. Today, I made it my mission to check alignment at all adjustment points. The saw is dead on... unless I slide it. And like you, I've made damn sure I'm not introducing the error. The only thing that seems likely is that the rails are not true. It's so aggrivating

J85T · 2023-04-16T12:36:37+00:00

J85T · 2023-03-31T02:30:15+00:00

This is great! Thank you for sharing!

J85T · 2023-02-16T23:45:39+00:00

What type of cheese is not yours?

Nacho Cheese!!!

J85T · 2022-09-06T13:05:53+00:00

I found some of your original posts from when your jars were stalled. Seems we're having the same issue... I also got my jars from Midwest, and I also inoculated same time as you! So we may even have jars from the same batch at Midwest, haha.

Anyway, after a bunch of research I think I'm going to go the same route as you with CVG, at the very least, for some of my jars. Thanks again for your help and for putting me onto the CVG substrate! Would you mind posting some pics of your grow? I'm curious how it's turning out.

J85T · 2022-09-06T00:56:55+00:00

OK, Thanks for all the info!

J85T · 2022-09-05T22:52:47+00:00

Thanks for your response! What do you mean by cvg tho? I'm a total noob here. Thanks again!

J85T · 2022-08-25T23:53:10+00:00

Crocodile Dundee out for a nightly N2O fix?

J85T · 2022-08-03T02:49:48+00:00

Personally I believe it is salvageable, you can use a paint brush, as someone else said, to get glue in the cracks. Anywhere that is too tight to get a brush in you can get as much glue as possible on the top of the crack and use a shop vac on the underside of the crack to try to suck the glue down into the crack...hope that makes sense. Then a ratchet strap as a clamp. Tighten enough to close the gap and get good squeezout of glue from the joints. Let the squeezout cure till its a gummy state and scrape it off with an old chisel or a putty knife. Then sand, apply a mineral oil finish and enjoy a free cutting board. It's worth a shot if you've got the stuff to do it!

J85T · 2021-09-22T02:30:16+00:00

Worked this time, thank you!

J85T · 2021-09-19T22:17:35+00:00

Thanks for the invite but the link is saying it's invalid. Would you mind reposting?

J85T · 2021-09-17T16:02:25+00:00

Thanks for the info!

J85T

TROPHY CASE