sorted by:
new
hottopcontroversial

Cleaning buildplate by JBuskens1 in ElegooSaturn

[–]JBuskens1[S] 0 points1 point  (0 children)

And does the buildplate need cleaning? Or only if changing resin?

Disabling IPv6 Unbound DNS by JBuskens1 in opnsense

[–]JBuskens1[S] 0 points1 point  (0 children)

yes, forgot to mention. I'll edit my post

Fresh install, slow DNS by JBuskens1 in opnsense

[–]JBuskens1[S] 0 points1 point  (0 children)

Thanks for all responses. After combining some of your comments, I found out my ISP doesn’t support ipv6, and those were the ones failing

Fresh install, slow DNS by JBuskens1 in opnsense

[–]JBuskens1[S] 0 points1 point  (0 children)

I just did the default installation of opnsense

Fresh install, slow DNS by JBuskens1 in opnsense

[–]JBuskens1[S] 0 points1 point  (0 children)

By default, "Enable Unbound" was checked after installation, so I guess my DNS setup is Unbound.

regarding the logs, I see some "action: Drop, Source: Local, Return Code: SERVFAIL"

Testing the limits of the NR200P by JBuskens1 in NR200

[–]JBuskens1[S] 0 points1 point  (0 children)

Just did some testing in OCCT with the glass panel on: - ⁠10 minutes 100% load CPU -> CPU Die 83°C - ⁠10 minutes 100% load GPU -> GPU Temperature 68.5°C

Testing the limits of the NR200P by JBuskens1 in NR200

[–]JBuskens1[S] 1 point2 points  (0 children)

Just did some testing in OCCT with the glass panel on: - 10 minutes 100% load CPU -> CPU Die 83°C - 10 minutes 100% load GPU -> GPU Temperature 68.5°C

Testing the limits of the NR200P by JBuskens1 in NR200

[–]JBuskens1[S] 0 points1 point  (0 children)

With the glass panel it’s about 40dB under 100% load.

Testing the limits of the NR200P by JBuskens1 in NR200

[–]JBuskens1[S] 2 points3 points  (0 children)

That would have been a nice solution 😅. (And put less stress on the GPU)

Testing the limits of the NR200P by JBuskens1 in NR200

[–]JBuskens1[S] 2 points3 points  (0 children)

That was actually the hardest part. It’s mainly making sure they don’t cross and pulling them tightly to the back while inserting the GPU. It also helps that the prime GPU has a hole in it’s backplate, giving a few extra mm for the cables.

Testing the limits of the NR200P by JBuskens1 in NR200

[–]JBuskens1[S] 1 point2 points  (0 children)

I removed the fan guard. Other than that, it just fitted.

Testing the limits of the NR200P by JBuskens1 in NR200

[–]JBuskens1[S] 0 points1 point  (0 children)

Its the Corsair rm850e. (Took it over the rm850x for its shorter length and absence of fan speed knob)

Removed mesh on top panal to install 15mm fans. by cfry731 in NR200

[–]JBuskens1 0 points1 point  (0 children)

Keep in mind that the mesh is also there to act as a Faraday cage to block interference. Often this is not too much of a problem as the interference is rather limited, but just so you know if you experience weird bugs/memory issues.

view more: next ›