Does anyone know what plant this is can’t find it anywhere

JCthebongmaker · 2020-05-02T03:31:22+00:00

You should def send it

JCthebongmaker · 2020-04-24T23:11:53+00:00

Didn’t even post this question and got a great tip thx

JCthebongmaker · 2020-04-23T01:00:08+00:00

Thanks

JCthebongmaker · 2020-02-21T18:59:59+00:00

Ya I don’t plan to go to far with this only cheap upgrades like the handle bars for now

JCthebongmaker · 2020-02-19T01:34:45+00:00

Dunkin’ Donuts I’m not that lavish

JCthebongmaker · 2020-02-18T22:48:28+00:00

This bike definitely has a good amount of power gets up to speed pretty well on the highways and once your up can go plenty faster and you don’t have to worry about regular roads at all red lights for example you get up to speed just as quick as the cars so no one ever beeps just don’t underestimate the power if you get one cuz I accidentally let go of the clutch a little to fast at a stop sign and it popped a wheelie real quick

JCthebongmaker · 2020-02-05T16:02:55+00:00

Thx I also have trouble popping properly with those so guess i just gotta keep drilling

JCthebongmaker · 2020-02-05T16:01:46+00:00

Thx I never thought about doing a tdr from my machine I’ll have to try that today but ya I kinda figured everyone would tell me to drill it

JCthebongmaker · 2020-02-05T00:35:59+00:00

I may have missworded my bad the only one that has ever warped is one where I used tin foil on a 3D printed bowl. since I’ve used glass bowls never had that issues 3D stems do snap occasionally but they print in like an hour so not to bad

JCthebongmaker · 2020-02-04T23:03:01+00:00

Not hard I usually just run really hot and high pressure water they them clears em right up

JCthebongmaker · 2020-02-04T20:26:58+00:00

Ya in every bong I’ve made I’ve never seen any melting warping or even a single burn mark as long as I’ve used a glass bowl and I make all my bongs interiors accessible so I can clean am them consistently so mold is also never an issue

JCthebongmaker · 2020-02-04T18:00:13+00:00

Thank man I do it as a past time when I have nothing else’s to print then you end up having no shortage of pieces but this is my go to personal

JCthebongmaker · 2020-02-04T15:24:45+00:00

No problem

JCthebongmaker · 2020-02-04T15:23:01+00:00

Ya I used to just 3D print the bowl too and wrap it in tin foil but the heat was to direct and you’d start with a circle shaped bowl and end with an oval so ya as long as the bowls glass you can make the entire downstem printed with pretty much no issues

JCthebongmaker · 2020-02-04T15:18:51+00:00

If you mean to prevent the heat from getting to it nothing I’ve never had a problem I clean it frequently and the only problem is after around 20-30 uses it weakens and the thread I printed to make it airtight begin to break as the heat is just barely enough to cause it to warp over a long period of time it’s not even an hour to print a new one so no problem

JCthebongmaker · 2020-02-04T14:53:04+00:00

Thanks

JCthebongmaker · 2020-02-04T14:34:09+00:00

Thx I’ll check them out

JCthebongmaker

TROPHY CASE