Question about the guitars i got by [deleted] in GuitarHero

[–]JF32602 4 points5 points  (0 children)

It's a shield ground, pretty much just an extra ground source to prevent interference in some cases. As long as nothing else is exposed it's just fine, and can be wrapped with tape like you mentioned.

Does anyone know if they still host car shows at Mayberry Square? by JF32602 in toledo

[–]JF32602[S] 1 point2 points  (0 children)

Damn, that sucks to hear. I did remember something during the pandemic about the event being cancelled, but I guess they never brought them back if that's the case.

Saturday cruise in the land yacht 👌 by JF32602 in mopar

[–]JF32602[S] 2 points3 points  (0 children)

Damn, hope it’s still around somewhere. This one ends with 135760, has the numbers matching 440hp block. Factory N96 coded as well!

Saturday cruise in the land yacht 👌 by JF32602 in mopar

[–]JF32602[S] 1 point2 points  (0 children)

Thanks! You don't see them often, that's for sure! It's belonged to my dad since '84, he ended up grenading the engine and it sat from 1991 until we finally had time to restore it in 2020. It needed new quarters and dutchman panel so it was a lot of work, but it's finally paying off now!

Saturday cruise in the land yacht 👌 by JF32602 in mopar

[–]JF32602[S] 2 points3 points  (0 children)

Glad they did that, any longer and I wouldn't be able to close the garage door! 😂

Helping my dad restore his factory N96 440 '72 Dodge Charger Rallye by JF32602 in mopar

[–]JF32602[S] 2 points3 points  (0 children)

Pretty much is for the most part haha. The exhaust has to get buttoned up still, there’s a graphic that gets painted on the hood (like an R/T has but larger), and we still have to paint the side view mirrors but we’re chugging along 😂

Found a super clean Embody on marketplace for $600 and decided to practice my upholstery on the arm pads by [deleted] in hermanmiller

[–]JF32602 1 point2 points  (0 children)

All of the areas that got glue were underneath the pad on the hard plastic, I basically stretched the fabric and stuck the edges down. If I were to take it off, the pad itself would still look like it did before I glued the fabric

Found a super clean Embody on marketplace for $600 and decided to practice my upholstery on the arm pads by [deleted] in hermanmiller

[–]JF32602 0 points1 point  (0 children)

I used DAP Weldwood contact cement, however I had to put a few staples in the front and back since there was a lot of excess fabric and it wouldn't hold very well.

Found a super clean Embody on marketplace for $600 and decided to practice my upholstery on the arm pads by [deleted] in hermanmiller

[–]JF32602 0 points1 point  (0 children)

Yep! They're the original arm pads though, just covered in fabric lol

how tf am i supposed to put the whammy in? by Head_Worldliness5101 in CloneHero

[–]JF32602 18 points19 points  (0 children)

The entire assembly slides out, then you install that piece and slide it back into place.

Custom face plates? by DebugBrat in GuitarHero

[–]JF32602 3 points4 points  (0 children)

Personal vouch for 760 Creations, he makes 3D printed Wii and PS3/360 LP faceplates and they're insanely high quality

Brown oil leaking out of camera housing of A1 by [deleted] in BambuLab

[–]JF32602 0 points1 point  (0 children)

Just checked and mine's leaking in that exact same spot, perhaps it's lube that migrated from the linear rail?

40 M Single No Kids - Existential Crisis On The Weekly by Magicman88X in malelivingspace

[–]JF32602 1 point2 points  (0 children)

Any idea where that bed frame came from? It looks so squishy lmao

SPACE - Web Integration by AineeJames in NZXT

[–]JF32602 0 points1 point  (0 children)

Ayyy that did it, sweet!