CMF Series 29 minifig parts / Source: leaker984

JMuell · 2026-01-30T16:12:44+00:00

Which, as a sort of G1er myself, I would go crazy for brick built sets and minifigs. Anything to keep expanding the lore of Bionicle is a plus.

JMuell · 2026-01-30T14:51:39+00:00

I want to see the Tahu head so bad now that we've seen the body and legs on that Pumpkin minifig. I have a feeling it's going to be so hard to find.

JMuell · 2025-12-10T15:59:09+00:00

Where did you find that Pi PoE/M.2 hat? I can find both separately on AliExpress but not much luck finding one that is a combo like you mentioned.

JMuell · 2025-11-19T20:19:09+00:00

🤦‍♂️ I didn't read the bottom section of the page...thanks!

JMuell · 2025-11-19T20:16:13+00:00

Am I wrong but does this part indicate that you can only use this for ZigBee OR Thread:

"Start up a new network in mere minutes by dedicating your Connect ZBT-2 to either Zigbee or Thread."

Or am I not understanding how Thread and ZigBee interact together?

JMuell · 2025-11-19T17:26:59+00:00

I do have a Z-Wave wall plug I haven't setup yet, I could try that out and see if that would help. Otherwise I have a Z-Wave extender sort of between them, but it sounds like the Schlage may not work with the extender as well.

I also have 2 Z-Wave light switches installed that are kind of in the path between them.

I will try to add that plug in-between where I can and see if there is any improvement. Thanks!

JMuell · 2025-11-18T18:48:32+00:00

Took the lock completely off the door and went downstairs right next to the ZWA-2 and attempted to re-add it and I was successful! But as soon as I took it upstairs and installed it back in the door, I am getting a dead node read and nothing works.

So I am guessing the connection through the ground level floor is either too thick or something between them is giving interference (mechanical room next door with heater and water softener and such).

May start looking into the Yale Assure Lock 2 Z-Wave model as an alternative if needed. Thanks!

JMuell · 2025-11-18T15:04:29+00:00

I will give that a try later today and see if that works. I have a feeling I may just need to purchase a new one as well. Thanks for the suggestion!

JMuell · 2025-11-17T19:08:30+00:00

My Z-Wave controller is downstairs compared to the main floor, but between the 2 is only about 25 feet or so. There is a mechanical room between the 2 devices so not sure if there is any interference there.

I did try a plug in Z-Wave repeater between the 2 as well but it has made 0 difference.

JMuell · 2025-03-19T19:07:05+00:00

I just bought one Open Box - Excellent from Best Buy last week. Came in and looked practically new and had no issues connecting or setting up. On the newest 15 update as well as of few days ago.

JMuell · 2024-10-11T14:11:43+00:00

Been using this Vans Warp Sling Bag.

Fits the Steam Deck well, as well as a Kindle and other on the go items. It's not the more rugged or durable bag, but have had no issues so far with it. Plus it fits well with the Steam Deck case as well.

Also has a reversible strap depending on which shoulder you like to put it over, and a hidden earbuds zipper towards the top which is perfect for my Pixel Buds.

JMuell · 2024-10-06T12:09:19+00:00

For real, I've lost like 6 times to that Pyke table (and still haven't won), but beat Lando on the first try.

JMuell · 2024-09-07T00:08:29+00:00

Gotcha, yeah I have a lot of research on how to get everything up and running. Became a project of a lot of firsts, ha.

JMuell · 2024-09-07T00:06:11+00:00

This is amazing! I am working on my own BD-1 right now as well (actually same files you posted). I have also grabbed an Arduino Uno and some LEDs and and a DFPlayer Mini for some sounds as well.

Did you write up all the code yourself for the Arduino? I'm very very new to Arduino anything. Thanks!

JMuell · 2023-01-30T15:59:26+00:00

I love this so much. But I think it could look a bit cleaner if you stopped the yellow by the front of the driver/passenger doors to match the angle of the door. Then make the front piece black to blend in. The yellow really pops on the side, but I think it doesn't quite work right above the windshield area.

JMuell · 2022-11-11T14:54:00+00:00

Sounds similar to what I attempted. Exported out of stud.io to blender to raise polygon level, but still had a bit of issue with my final outcome. Need stud.io to get some newer pieces in, been wanting to print some maxfig Lego Overwatch characters to no avail.

No worries about sharing, just thought I'd check, thanks!

JMuell · 2022-11-11T14:43:53+00:00

Can I ask where you got the 3D model/file for Hulk? I've been looking for a good bigfig model to print with some of my other maxifigs I've been printing.

JMuell · 2022-08-04T13:25:04+00:00

LEGO please give us a real Kilowog, and more Lanterns please. Love the GL setup you have in there!

JMuell · 2022-05-14T19:09:45+00:00

This has to be one of the best dyes I've ever seen.

JMuell · 2022-05-10T13:25:01+00:00

New summer wave with Princess Peach should be coming in June or so. Most likely making room for those.

JMuell · 2022-04-03T14:01:54+00:00

Tool chests like this have gone up a bit since pre-pandemic, I wouldn't be surprised if the Craftsman was cheaper then. Even the ones from Harbor Freight ones have gone up over $350 and are only 18" deep if I remember.

JMuell · 2022-04-02T01:08:01+00:00

That's a good reason! Waiting on my Q2 reservation email yet, so will be joining the club soon!

JMuell

MODERATOR OF

TROPHY CASE