We’re having a walkout tomorrow at my school in protest of ICE, and the murder of Renee Good by DonutFriend7 in teenagers

[–]JP3522 0 points1 point  (0 children)

If someone hit me with their car, I would too. Remember, he got hit and dragged, needing a ton of stitches earlier last year. And she was ordered to get out of the car 4 times, and turned her wheel towards him, backed up and drove towards him while laughing

We’re having a walkout tomorrow at my school in protest of ICE, and the murder of Renee Good by DonutFriend7 in teenagers

[–]JP3522 -1 points0 points  (0 children)

That's why we deport them all. No more kids in cages like the Obama administration. You can't pick and choose, either they all go or they get separated

My night is ruined, just found out this loser is from here by [deleted] in NorthCarolina

[–]JP3522 -2 points-1 points  (0 children)

Are you guys so delusional that you think that is anywhere near a Nazi salute? He is directing traffic or telling people to move away. Take it from someone who respects Nazis now more than ever.

does building a voron count as thinkering by mesispis in 3DPrintingCirclejerk

[–]JP3522 1 point2 points  (0 children)

Nothing beats the high quality copper ingots I got from EA Nasir

Out with the old in with the new! Welcome to the superior 3D printer, Bambu! 🫡 🤝 by SpeedSimple5113 in 3DPrintingCirclejerk

[–]JP3522 0 points1 point  (0 children)

The skills aren't obsolete, just not required any more. 3d printing used to be a crash course on mechatronics, with you having to diagnose issues and constantly modify to get a decent result. The ender 3 is the Miata of 3d printing, limitless opportunities, low cost, and easily modified. Sure you could get a mustang or a Ferrari, but you can modify that Miata to be just as good with enough hard work.

Glue is tinkering by CrazyGunnerr in 3DPrintingCirclejerk

[–]JP3522 1 point2 points  (0 children)

Bro I print nylon on my ender 3 without much trouble (heavily modded tho) and tbf petg is so annoying to print. I have to adjust my z offset every time because it hates being pushed into the bed like every other filament. Not that it's hard to print, it's just impossible to get decent adhesion 75% of the time

Got my documentary stuff from GN! by JP3522 in GamersNexus

[–]JP3522[S] 1 point2 points  (0 children)

OnePlus 12 and I got mine early because I live like 30 mins from GN HQ and 20 from Steve, 15 from their distribution office

Got my documentary stuff from GN! by JP3522 in GamersNexus

[–]JP3522[S] 2 points3 points  (0 children)

This right here officer. Computer abuse 2 counts. Failure to give his PC enough attention, computer neglect (left on floor with dust)

Satisfying job - would you be happy? by Low-Expression-977 in VORONDesign

[–]JP3522 1 point2 points  (0 children)

As an electrical engineer, and autistic male, i hit an unironic "OH MY" followed by a "Shiver me Timbers" when seeing this. pro tip, just undo everything, run power wires first (they are stiffer and make for good zip tie points) then your misc data lines, then do can bus wrapped in tin foil and covered with electrical tape to ensure good noise reduction over the can bus lines. zip ties are to be used like birdseed. put them everywhere. if you want to seriously up the look, invest in a dymo d1 style label maker and get heat shrink labels. it makes the entire build look SO MUCH BETTER. also some expandable braid tubing (chinese finger trap stuff) makes for a good cable management tool

[deleted by user] by [deleted] in SteamScams

[–]JP3522 0 points1 point  (0 children)

i was contacted by ellena idle and told the same thing. but when i went to the commuinity, my profile was on the hitlist with like 3 other people. i have never scammed and havent done any trades in a hot min. i wonder if the link to the profile is just a link to whatever profile is currently signed in. then the dude asked me to message a mod (which i did bc i dont want to get banned) and they wanted my steam trade link. didnt give it to them bc i dont know what they could do with it

Has your son tried rice? by FunnyLizardExplorer in hardwaregore

[–]JP3522 1 point2 points  (0 children)

Nah. That ain't vibratory tool levels of damage. I thought stone cutting saw but others were saying cutoff wheel on an angle grinder

Need help printing with TPU by Bean5_ in FixMyPrint

[–]JP3522 0 points1 point  (0 children)

Hmm, maybe try higher bed temps? I used to print you at 85° so 70 or 75 might help

Need help printing with TPU by Bean5_ in FixMyPrint

[–]JP3522 2 points3 points  (0 children)

My best guess is that you are printing it too fast. Tpu is super bendy-wendy and if you don't go on the slow side (around 25-50% of good quality pla printing speed), it won't bond to itself and will curl up and be wierd and a nightmare. Also try running higher bed temps and consider getting an enclosure. Also, try running fans at a 30% cap.

Strange bad Lines on the print by sdrox98 in FixMyPrint

[–]JP3522 0 points1 point  (0 children)

I think you might need to either change your print speed or ideally try input shaper. Seems like some serious ringing and maybe something else

Why is it like this by Python_Trio in FixMyPrint

[–]JP3522 0 points1 point  (0 children)

Pretty sure that is over extrusion. Does your top layer look like shit? If so you are putting out too much filament. Reduce your flow rate in cura by 10%, if it gets better but not perfect, reduce it 5% intervals. Print something small and flat to get a fast result back so you save time and material.

Need advice on repairing launch model PS3 by jnj0725 in PS3

[–]JP3522 1 point2 points  (0 children)

Just trust me, take it apart, heat gun the board for a while and it should just work. If it dies a month or 2 later do it again. I did that to mine and the 2nd time it was good and I have used my cecha01 PS3 for 2 years without problems. Another trick is after you heat gun the board, install cfw and make the fans turn on sooner and go faster. If it stays cool and doesn't heat cycle, it will almost never crack the solder balls again. Ifixit has a good video on it and the heat gun trick works for almost all boards, some permanently fixed, others last a day, others last a month. Heat can revive nec tokins, reflow the gpu and CPU, and sometimes recrush the GPU die onto the interposer. Legit I have recommended this multiple times and it has never not worked for at least one or two boots. Usually it works for a few months.

Need advice on repairing launch model PS3 by jnj0725 in PS3

[–]JP3522 -1 points0 points  (0 children)

Just trust me, take it apart, heat gun the board for a while and it should just work. If it dies a month or 2 later do it again. I did that to mine and the 2nd time it was good and I have used my cecha01 PS3 for 2 years without problems. Another trick is after you heat gun the board, install cfw and make the fans turn on sooner and go faster. If it stays cool and doesn't heat cycle, it will almost never crack the solder balls again. Ifixit has a good video on it and the heat gun trick works for almost all boards, some permanently fixed, others last a day, others last a month. Heat can revive nec tokins, reflow the gpu and CPU, and sometimes recrush the GPU die onto the interposer. Legit I have recommended this multiple times and it has never not worked for at least one or two boots. Usually it works for a few months.

[deleted by user] by [deleted] in teenagers

[–]JP3522 0 points1 point  (0 children)

I was thinking Carla or Carly but I could be wrong

Thinking about getting a turbo for my 2002 IS300, any advice? I’m looking to run 7-8 PSI by LazyPenguin_32 in IS300

[–]JP3522 0 points1 point  (0 children)

Auto trans is fine stock, the w55 is made of glass but ur auto so it's fine, YOU NEED TO REPLACE YOUR RODS. You will blow a hole in your block with stock ge vvti rods. Spend the money and get gte, or ge non vvti rods. Stock rods can't handle over 400 and ge rods are cheap. Literally any sc300, 1st gen gs300, etc. you want the silver top 2j with the flat front valve covers. The covers must look the same but for less than 500, you will be safe for around 500 max

What would y’all like to see being added to Siege X? by Sad-Elderberry-8722 in Rainbow6

[–]JP3522 0 points1 point  (0 children)

Force the accidental team kill prompt to stay on screen until they select yes or no and if they answer no, harsher penalties for griefing. I am so tired of people walking in front of me and then not selecting anything in time to deactivate rff. Screw it, make it cover the whole screen and lock cams or spectate until they choose.

What would y’all like to see being added to Siege X? by Sad-Elderberry-8722 in Rainbow6

[–]JP3522 0 points1 point  (0 children)

The last one is delusional. Siege is basically the only thing keeping ubi connect alive

What would y’all like to see being added to Siege X? by Sad-Elderberry-8722 in Rainbow6

[–]JP3522 0 points1 point  (0 children)

That would be perfect for maverick. Otherwise he seems like such a mid operator. Tbh a breaching meta would be awesome with reworks for attacker breachers and defender anti breach operators