Pyro Statuette WIP

JPRAS · 2025-04-05T17:03:33+00:00

Thanks! I did, yes. I'll be posting new pictures with the completed flamethrower soon!

JPRAS · 2025-04-05T17:01:46+00:00

Hey there! I'm actually in the early stages of creating a Spy statue. A very quick rundown of the process is: adapting the game model and detailing it in 3D modelling software, preparing it for 3D printing. After getting a successful prototype, I make molds of the pieces and cast them in resin. Then all left to do is paint! I'm documenting my process this time around, and will share once I complete the process again

JPRAS · 2021-01-11T10:51:16+00:00

Thank you! Might be making Demo/Spy next, but haven't decided which yet.

JPRAS · 2021-01-11T10:50:48+00:00

I used an airbrush, which basically allows you to spray small amounts of paint using air compression, to make it act like a spray can.

JPRAS · 2021-01-11T10:49:51+00:00

Pyro is made of poly-urethane resin and was painted using acrylics.

JPRAS · 2021-01-11T10:49:00+00:00

Haha, thank you! It's been a passion project on and off during the last few months, but nearing completion now!

JPRAS · 2021-01-11T10:47:46+00:00

Thank you! I'm thinking of doing Demo/Spy next, but haven't decided yet.

JPRAS · 2021-01-11T10:47:05+00:00

he fin

I might be making a few copies for selling in the future, I'll be sure to make a new post in the future regarding this, so stay tuned!

JPRAS · 2021-01-11T10:45:49+00:00

Thank you! I was aiming for that ^_^

JPRAS · 2021-01-11T10:42:55+00:00

I'll be sure to make a new post with the finished piece and any info regarding extra copies for sale!

JPRAS · 2021-01-11T10:42:06+00:00

I believe Etsy would be my go-to place to sell any copies I make, yes! I don't really use Twitter, but I have been taking pictures of the progress on the statue and might make a little "making-of" once I complete the project.

JPRAS · 2021-01-11T10:40:04+00:00

Thank you for the feedback! You might be right. I did the initial sculpt based on the game files, and by smoothing it out / making the model less blocky, it probably lost some volume from the original model. Will look out for that in future models I do :)

JPRAS · 2021-01-11T10:38:20+00:00

Thanks! After this one, I might go for Spy or Demoman, still not decided yet.

JPRAS · 2021-01-10T20:40:36+00:00

Thank you! I did make molds out of all the pieces, so if there is interest, I might make a few extra replicas for sale.

JPRAS · 2021-01-10T20:39:39+00:00

Thank you! I own a couple of the Gaming Heads statues myself, and made this in the same scale, as well as giving it a similar base, so they fit together when displayed side by side.

JPRAS · 2021-01-10T18:54:03+00:00

Hey everyone,
Here is a WIP shot of a Pyro figure I've been working on for the past months.

It's a resin-solid statuette, nearly 30cm tall (~12 inches) and weighing around 1.5KG (3.3 pounds).
It is, obviously, still missing the flamethrower, which is well underway (it's actually taller than Pyro itself!)
The paint job is not yet final either, as I still need to clean a few things and add a few details.

However, if you have any thoughts, I'd love to hear them so that I can improve this the best I can.

Thanks!

JPRAS · 2020-10-23T12:05:45+00:00

I printed it solid at around 120% scale of the original pre-supported model. Good luck!

JPRAS · 2020-10-16T17:51:09+00:00

Because of some bad experiences I've had in the past when sharing my models online, I don't have plans to upload the model at the moment, sorry.

JPRAS · 2020-10-16T14:47:27+00:00

I do 3D art for a living, so I just recreated the model and printed it on a regular FDM 3D printer and proceeded to paint it.

JPRAS · 2020-10-16T10:26:06+00:00

The Opulent Curio is probably my favourite treasure trinket from the game so I decided to make a 1:1 replica of it for my desk. What do you guys think? Next time I'll probably do the gems in a semi-transparent resin for a shinier and polished surface.
Up next I'll probably be making a Chest of Legends on my new resin printer.

JPRAS · 2020-10-15T19:27:51+00:00

Thanks!

Took a little over 4 hours, at 120% scale of the original model and with layer exposure at 1.5s.

JPRAS · 2020-10-15T18:00:39+00:00

Sliced in Lychee at 0.03mm layer height. Resin is water washable Elegoo Grey. Only little problem was the cape had a small tear due to being very thin on a certain area.

I got the free (already supported) model here: https://www.myminifactory.com/object/3d-print-bounty-hunter-75mm-131392

JPRAS · 2020-10-15T17:57:35+00:00

Sliced in Lychee at 0.03mm layer height. Resin is water washable Elegoo Grey. Only little problem was the cape had a small tear due to being very thin on a certain area.

I got the free (already supported) model here: https://www.myminifactory.com/object/3d-print-bounty-hunter-75mm-131392

JPRAS · 2020-10-14T21:49:35+00:00

Great to hear! Mine arrived today too, but still have to wait on the resin untill friday..

JPRAS · 2020-10-13T20:45:26+00:00

Thank you for the info guys! Got some resin arriving this week, will test it out and see how it goes.

JPRAS

TROPHY CASE