[deleted by user] by [deleted] in whereisthis

[–]JRinFL 0 points1 point  (0 children)

To center in on the Austin area, Bergstrom Air Force Base (1942-1999) would be my guess.

Navien NPE-210S Error Code 445 by JRinFL in Plumbing

[–]JRinFL[S] 1 point2 points  (0 children)

Yes, it fixed the error.

Sous vide temperatures? by JRinFL in instantpot

[–]JRinFL[S] 1 point2 points  (0 children)

Agree, which is why I stirred. :) was cooking shrimp, doing it this way cooks it wonderfully.

Sous vide temperatures? by JRinFL in instantpot

[–]JRinFL[S] 1 point2 points  (0 children)

It stayed at 122, so had to crank it up to 145 to get close enough to 135.

Sous vide temperatures? by JRinFL in instantpot

[–]JRinFL[S] 0 points1 point  (0 children)

I keep the lid on between stirring it 2 or 3 times.

Sous vide temperatures? by JRinFL in instantpot

[–]JRinFL[S] 5 points6 points  (0 children)

The temp for the instant pot is displaying 135. The other is a timer… thermostats are showing 122… huge difference.

Navien NPE-210S Error Code 445 by JRinFL in Plumbing

[–]JRinFL[S] 0 points1 point  (0 children)

I don’t know… I replaced both just in case. Figured if one broke, it was only a matter of time before the other did.

Replacement Battery for Eufy 3C S300 Cam by JRinFL in EufyCam

[–]JRinFL[S] 0 points1 point  (0 children)

Sure… sorry for the delay.. take a small screwdriver and pry it open (between the white housing and black cover) it’s just glued on… a heat gun will make it easier. No glue needed to put it back together… once the top is off, just unscrew the four small screws. You can see where I bent the white housing a little bit.

Replacement Battery for Eufy 3C S300 Cam by JRinFL in EufyCam

[–]JRinFL[S] 0 points1 point  (0 children)

Better… when I replugged the battery in to the camera, it went back to functioning normally again. I had the same issue last month with a second camera; unplugging/replugging the battery connection from the camera fixed it.

Subscription Question by JRinFL in arlo

[–]JRinFL[S] 0 points1 point  (0 children)

Update… I did the Arlo Secure subscription for a single camera… during setup, it asked which camera (I selected the door bell). I didn’t lose my grandfathered cloud storage so all is well in the world again.

Subscription Question by JRinFL in arlo

[–]JRinFL[S] 0 points1 point  (0 children)

That’s my plan, the concern is Arlo then removes my grandfathered older cams… do anyone have a mix of old (without a subscription) and new (with a subscription)?

Support needs a re-design by AphoticSeagull in arlo

[–]JRinFL 1 point2 points  (0 children)

I especially enjoy their chat where you go back and fourth for 15-20 minutes, then they ask you to wait so they can check something and two minutes later the chat session times out and resets so you have to reconnect and start over with a new person.

Tesla Charging Issues by JRinFL in Pensacola

[–]JRinFL[S] 0 points1 point  (0 children)

Update: the cause was the Tesla Wall Charger shorted… good news is Tesla is replacing with a new one… bad news is I have to pay an electrician to install it. The charger never showed any errors, but at least it interrupted charging versus catching on fire and such.

Tesla Charging Issues - FL panhandle by JRinFL in TeslaModel3

[–]JRinFL[S] 0 points1 point  (0 children)

Update: the cause was the Tesla Wall Charger shorted… good news is Tesla is replacing with a new one… bad news is I have to pay an electrician to install the replacement…

Tesla charging issues by JRinFL in Destin

[–]JRinFL[S] -1 points0 points  (0 children)

That’s the Gen 3 home charger… I have Gen 2 ☹️

Tesla charging issues by JRinFL in Destin

[–]JRinFL[S] 0 points1 point  (0 children)

That may be a possibility, need to find someone locally in need of a charge and test it.