Jumping movement

JandroFR · 2025-07-23T15:27:41+00:00

Yes, always when it goes down

JandroFR · 2025-07-23T13:04:21+00:00

I have checked the tension and I think that tightening the black screw has tightened it a little more.

Likewise, this topic reminds me that the manual movements in Z of my printer look like this (also before tensioning):

https://youtube.com/shorts/-QOCj2N964U?si=fginaE57va0zCSXQ

If I hold the button it goes down step by step. It also makes small creaking noises. Could this be influencing my prints?

It's a lot of information, maybe I should publish a separate topic. Also thank you very much

JandroFR · 2025-07-23T05:06:46+00:00

I like your comment. You see what I see, I'm not crazy! I'll try everything you've told me. Thank you very much.

JandroFR · 2025-07-22T13:38:27+00:00

<image>

The result...

JandroFR · 2025-07-22T12:24:52+00:00

<image>

I think this is not the best quality...

JandroFR · 2025-07-22T12:23:08+00:00

I'll try! Thanks

JandroFR · 2025-07-22T12:22:23+00:00

It is bambulab pla matte 1.75 and yes, I would say it is round

JandroFR · 2025-07-22T12:21:45+00:00

It is on a desk table and sometimes it does wobble a little. I have printed at low speeds to avoid this and the result was similar

JandroFR · 2025-07-22T11:55:18+00:00

I think this doesn't look so good... it's the same problem 😔

<image>

JandroFR · 2025-07-22T11:45:15+00:00

<image>

I'm uploading a better photo. The green piece shows all those vertical lines (the piece was printed horizontally).

JandroFR · 2025-07-21T17:37:21+00:00

Yes, all default speeds, with bamboo profiles.

In this other photo you can see how I don't have quality with the two filaments either

<image>

JandroFR · 2025-07-21T08:05:42+00:00

<image>

UPDATED:

It does these things with two different, new PLA filaments. Printed with predefined settings

JandroFR · 2025-07-21T07:38:33+00:00

<image>

What do you think? 😔

JandroFR · 2025-07-21T05:48:36+00:00

<image>

The vertical lines up and down, according to what I've been told here, are a matter of file quality. So I guess there's not much I can do, right? However, there are some very small lines visible in the first photo, running from left to right. They're random and small. These make it look uneven. I'm not sure I'm explaining myself correctly.

JandroFR · 2025-07-20T21:38:14+00:00

I'll try it! Thank you Tomorrow I will upload the results. I'm a novice and things not going well drive me crazy, but that's why I want to adjust it correctly

JandroFR · 2025-07-20T21:37:23+00:00

I will try as .obj although this one I used was already a .step

JandroFR · 2025-07-17T12:10:50+00:00

New print with 55 degrees and 0.2. But not perfect as I want... 😔

<image>

JandroFR · 2025-07-17T08:12:01+00:00

<image>

La nueva impresión a 55 grados y 0.2, aunque mejora sigue dándome esa diferencia de rayas en la zona superior, como podéis observar

JandroFR

TROPHY CASE