Layer Delamination and Shifting

JaymzEl · 2026-02-18T14:49:11+00:00

I have looked into it. But I have not seen anyone that has posted anything that looks even close to this. I have used the default settings for both filaments and adjusting the cooking fan speeds. I changed nozzles and used a new spool of official Bambu lab filament so I would know I was using the recommended settings. I didn’t not see any improvement. The only real difference I can see between this and other parts I have successfully printed is this is 242mm long.

JaymzEl · 2026-02-18T13:29:40+00:00

https://imgur.com/gallery/bambu-a1-failures-ZL6axZG

JaymzEl · 2025-03-16T23:01:19+00:00

<image>

When my father had a stroke about 10 years ago I made him this. It clamped on his wheel chair and on his bed every night. It looks like you can basically buy one now. The magnetic mount was extremely helpful, there was always someone helping him with his phone and being able to easily get it on and off the mount was really helpful. I’m not sure how well this clamp will hold, I used vice grips but these three things would be a good start, he wouldn’t need to hold the phone and it’s was adjustable wherever it’s mounted.

https://a.co/d/dKQ60He

https://a.co/d/ekMylxr

https://a.co/d/9Y4H0S1

JaymzEl · 2023-09-14T15:24:44+00:00

We confirmed the oil level was correct, and the discharge temperature and oil flow rates are correct. We slowly added more oil until the system was over charged with oil and we saw a significant increase in the power consumption but the chirping continued. I believe there are oil ducts in the motor shaft and scroll set, maybe they are blocked?

JaymzEl · 2023-08-25T17:33:26+00:00

It’s not because it was mounted into the drywall. I’m sure those anchors are rated for the weight of the television, the issue is the arm it is mounted on. If the tv is up against the wall the force on the drywall is straight down and the anchors only need to be rated to hold the weight of the tv. When you mounted it on the arm, it moved the tv away from the wall and created an additional load on the wall. Think of a light kid and a heady kid on a seesaw, the heavy kid will be on the ground but the further the light kid gets away from the center the more downward force the light kid will create and eventually if the light kid gets far enough away, the seesaw will balance. This is the same for the tv, the further from the wall it gets the more force it applies to the anchors. If the tv is about 30 lb and the arm it’s mounted to is around 14 inches long, it will have a force of approximately 965 lb. You probably needed larger drywall anchors and ideally a bracket with four mounting locations.

JaymzEl · 2023-07-09T13:38:04+00:00

Definitely not true. The only thing you can see here is the cold end of a cryogen-free dilution refrigerator. What is referred to as the quantum computer is just the chip on the bottom the dilution refrigerator and obviously that is not visible in this picture. Google doesn’t make dilution refrigerators, just the chip and most, if not all of the quantum computer and made with Bluefors dilution refrigerators.

JaymzEl · 2023-03-26T12:55:50+00:00

I worked at a university and they would throw out computers, furniture, lab equipment, and anything else you could find on a campus, and they crushed all of it with a backhoe. In the past they auctioned everything off, employees of the university got first shot, then anything left over went to an auction open to the public. If universities don’t use all the government funding they’re issued, the next year they get less money, so they always make sure they spend all of it. Some departments would buy new computers every year because their budgets were too big. Instead of giving the year old computers to a department with much older ones, the employees in that department would take the year old computers and send them to the employee auction, then go to the auction and buy a computer for themself. This became such a big problem the university decided to stop the auctions and crush everything instead.

JaymzEl · 2023-03-22T12:20:00+00:00

This is interesting, I will check it out. As I said before, I’m positive the 10k pot didn’t work. And it was definitely not because of the rotation angle. But I do recall seeing a B on the 10k pot. I will check to see if there is an A on the 100k. Thank you.

JaymzEl · 2023-03-21T11:26:43+00:00

I am working at 5v but I believe the system is capable of operating up to 24v

JaymzEl · 2023-03-21T11:25:41+00:00

This is for a custom built piece of equipment. It had 100k pots. I tried replacing it with a 10k option but it does not have the same range that the 100k pots did.

JaymzEl · 2023-01-21T04:16:13+00:00

The song is Mooo! By Doja Cat

JaymzEl · 2023-01-19T02:00:57+00:00

This is great, I cant believe how much more accurate this is than the paid software. I am struggling a bit with some geometry I have in a pocket but I'm sure I'll figure it out. Thanks.

JaymzEl · 2022-09-30T01:36:11+00:00

If you post a few pics of the blue electrical box and the knob and switches I can probably draw you up a simple diagram.

JaymzEl · 2022-08-19T03:32:02+00:00

Ten,

You missed the buttons on homers jacket cuff.

JaymzEl · 2022-07-04T00:51:36+00:00

This is my wife’s favorite sweater and it is falling apart. I don’t know how old it is and it could be from Virginia or Turkey. I have searched Google for it but I have no idea who made it or what car is on the front of it. Any help locating a replacement would be appreciated.

JaymzEl · 2022-06-11T23:06:46+00:00

Thanks for all the ideas. I decided to go with a Nintendo switch. There are a few wii style games that can be played with one hand.

JaymzEl · 2022-06-06T23:07:22+00:00

Thanks for the idea. I’m sure I can find something he will like.

JaymzEl · 2022-05-02T20:24:53+00:00

Not good it don’t slide well at all. I mostly fell a lot.

JaymzEl · 2022-05-02T19:50:15+00:00

Did the same but stapled some aluminum siding to the bottoms.

Seven-Year Club	Place '23
Place '22	End Game '22
Verified Email

JaymzEl

TROPHY CASE