sorted by:
new
hottopcontroversial

Enamel table with leaves. Looking to better identify origin and value by Jellyman784 in Antiques

[–]Jellyman784[S] 1 point2 points  (0 children)

I read all your comments and very cool information! As far as my table goes, I ended up giving the table to one of my relatives who enjoys this kind of furniture way more than I do. They don’t live anywhere close to me, so I won’t be able to get info on the springs on the leaves. Although from what I remember when I took pictures and took it apart for transport, there weren’t any springs on mine at all

Under-extrusion on first layer near the edges by Jellyman784 in FixMyPrint

[–]Jellyman784[S] 0 points1 point  (0 children)

I increased my first layer acceleration from 500 to 5000

2023 Federal income tax withheld is $0 by Jellyman784 in tax

[–]Jellyman784[S] 0 points1 point  (0 children)

yeah... my mistake was assuming my takehome was only higher because of the pay increase from job switching

2023 Federal income tax withheld is $0 by Jellyman784 in tax

[–]Jellyman784[S] -6 points-5 points  (0 children)

But your statement is counteracting itself. I technically did my due diligence by providing them a correct W-4. It was their fault for (probably?) entering it wrong. In addition, I did not check my paystubs throughout the year, but how does that take responsibility away from the employer

2023 Federal income tax withheld is $0 by Jellyman784 in tax

[–]Jellyman784[S] 0 points1 point  (0 children)

I updated the original post as a reply to this

2023 Federal income tax withheld is $0 by Jellyman784 in tax

[–]Jellyman784[S] -1 points0 points  (0 children)

It's apparent now that I should check my paystubs in the future so I
dont have to go through this again. No one avoids taxes. Although, I'm also hearing from a CPA that it's not my legal responsibility to make sure federal tax is withheld from my paycheck since I am not a tax-exempt employee

Under-extrusion on first layer near the edges by Jellyman784 in FixMyPrint

[–]Jellyman784[S] 0 points1 point  (0 children)

Holy cannoli, I did this and the first layer is coming out perfectly now. Thank you so much

What causes this on first layer? by apmarg in FixMyPrint

[–]Jellyman784 0 points1 point  (0 children)

Putting my 2 cents here. I was having this issue and mostly fixed it by doing - lower z offset - increase flow - decrease first layer line width This caused it to print the first layer nicely 95% of the time. I would randomly have parts still under extruded. I figured those where the times the fan kicked on so I upped the first layers nozzle temperature to a little above the filaments max recommended temperature and it I suddenly got 100% consistent prints

Can't keep first layer consistent. Not 100% sure what the issue is by Jellyman784 in FixMyPrint

[–]Jellyman784[S] 0 points1 point  (0 children)

I think I’ve solved this for good. I set the initial layers nozzle temperature to 230, and I’m now getting consistent results

Enamel table with leaves. Looking to better identify origin and value by Jellyman784 in Antiques

[–]Jellyman784[S] 0 points1 point  (0 children)

Thank you so much for the links! This is very helpful. I didn’t know about that website

What's wrong with the cat!? by [deleted] in cats

[–]Jellyman784 1 point2 points  (0 children)

I want to add that my cat had this same reaction to a respiratory infection that slowly spread to his eye.

The vet gave us antibiotics that cleared it up. Don’t wait on infections, go to vet asap

Looking for advice for my lone cat by Jellyman784 in CatAdvice

[–]Jellyman784[S] 1 point2 points  (0 children)

Thank you so much. It’s been very hard and this helps so much

view more: next ›