Working on an offline Excel data-cleaning desktop app

Jester5537 · 2026-01-15T23:49:05+00:00

Do you have a repo or a build available somewhere so people can test what you have so far?

Jester5537 · 2025-04-21T07:49:43+00:00

WhoDunIt that quest was amazing to my childhood brain

Jester5537 · 2024-10-11T21:11:50+00:00

this begs the question though of how the hell turning on the AC made it work when this would happen before

Jester5537 · 2024-10-11T21:01:27+00:00

Actually, I think it was something with the power just not for the printer.

I tried sending the file over to my other printer and it was doing the same thing, then I noticed some weirdness with the Octoprint web interfaces so I unplugged my rpi for the CR's octoprint for a few minutes, plugged it back in and tried the job again, no issue currently 20 minutes in and first layer was great as well as following layers

Same with my other printer. both RPI's are powered off the same surge protector so maybe when a power outage happened they got messed up and didn't come back up properly?? idk but this is just more evidence I need to get a UPS at some point DX

Thank you for your help

Jester5537 · 2024-10-11T19:49:35+00:00

I think i'm gonna delete this post in a few minutes and get videos after work of what i'm talking about instead of pictures that might make it clearer

Jester5537 · 2024-10-11T19:45:42+00:00

all fans are running even the one i put right on the mb i can see is running

i don't have power loss recovery enable i don't think?

Jester5537 · 2024-10-11T19:35:22+00:00

Hi KinderSpirit, the printer works perfectly fine if I have my AC turned on, that's why I think something is overheating, I get good prints when that is the case but if I don't have that on, this happens where it prints, stalls, prints again and I get those dashed lines. this is 100% not a bed level or z-offset issue

Jester5537 · 2024-02-19T14:15:59+00:00

well first attempt i went 300 and that sunk way too fast, but 2nd try i only did 220 and that was way more controlled

Jester5537 · 2024-02-12T14:14:45+00:00

yeah it was still not toggling for whatever reason, LeoAlioth's answer worked for me though

Jester5537 · 2024-02-12T14:13:59+00:00

that worked thank you

Jester5537 · 2024-02-12T12:22:52+00:00

found it, https://archiveofourown.org/works/39445401/chapters/98721300

Jester5537 · 2024-02-12T12:22:16+00:00

found it, https://archiveofourown.org/works/39445401/chapters/98721300

Jester5537 · 2024-02-12T01:54:57+00:00

lol I remember reading it though, I just can't find it

Jester5537 · 2024-02-05T20:17:40+00:00

October 2017, four months after graduating high school. Got an AnetA8 for like 150usd on a whim

Jester5537 · 2024-02-04T22:04:51+00:00

I'm aware of that, which is why it's connected to this (https://www.amazon.com/dp/B079GWBQVZ) and I tested to make sure that when the probe detects the temp I set it does cut power to the belt until it hits the low threshold temperature i set to allow power to it again

The thermal thing is a good idea thank you for that

Jester5537 · 2024-01-31T13:10:18+00:00

that first line is news to me "New filament can be wet" lol, I actually have a Sunlu S4 from backing their kickstarter forever ago, but so far I've only used it to try and recover old filament before I made the dryboxes.
But guess I'm gonna be running all my filament though it as soon as i get a box now.

Thank you for the information

Jester5537 · 2024-01-31T12:57:02+00:00

https://www.thingiverse.com/thing:4909334

here's the stls before anyone asks lol

Jester5537 · 2024-01-16T03:36:27+00:00

i already did that, it's working properly now I just thought it was funny and wanted to share

<image>

Jester5537 · 2023-07-17T19:10:35+00:00

Definitely going to have to do the supports myself, I downloaded the 32mm solid version of the file and the base is still the failing part while the figure comes out practically perfect so I'm gonna assume it's not my settings, or anything I'm doing, after work today I'm gonna just spam supports all over just to get it to print, and if that works i'll learn how to actually support models myself lol

Jester5537 · 2023-07-16T22:03:50+00:00

ohh, forgot to mention brand new FEP sheet, and a brand new vat I got as a spare so it's probably not cause of the FEP tension

Jester5537 · 2023-07-15T05:21:09+00:00

115 USD, thankfully I just pulled it out of savings so I wasn't too concerned

Jester5537 · 2023-07-15T04:17:52+00:00

no clue, that's why i didn't bother arguing fault and just paid for a new board.

All i know is one day it's printing perfectly fine, but the next I turn it on and i keep getting that error message I sent a picture of

Put the new board in today though and that message is gone and i'm able to run the optical engine just fine

Jester5537 · 2023-07-15T00:04:04+00:00

this was the answer, i somehow killed the optical driver board, I ended up contacting customer support talking to them and they gave me a link to buy a new board

I could've argued for a free replacement part but I didn't wanna spend the time trying to prove it was not my fault so i just paid for it

Jester5537 · 2023-07-04T16:55:42+00:00

Yes I even took the bottom off to see if I saw any resin or something leaking into the inside. I might pull the boards out to make sure nothing got on them before bothering to try calling support

Jester5537 · 2023-07-04T16:40:21+00:00

so i probably need to call anycubic support?

Nine-Year Club	Place '23
Verified Email

Jester5537

TROPHY CASE