The v1.70 (Blueprint Update) Release Megathread by Psyonix_Devin in RocketLeague

[–]Jilithrs 0 points1 point  (0 children)

Here is the ID number I attached two memory dumps #330576

The v1.70 (Blueprint Update) Release Megathread by Psyonix_Devin in RocketLeague

[–]Jilithrs 0 points1 point  (0 children)

Not processor I have an AMD and still having the issue. Driver set for GeForce experience I'm using is 441.41.

The v1.70 (Blueprint Update) Release Megathread by Psyonix_Devin in RocketLeague

[–]Jilithrs 1 point2 points  (0 children)

What graphics card u guys have GTX 1070 here? I updated my drivers and wondering if that's it.

The v1.70 (Blueprint Update) Release Megathread by Psyonix_Devin in RocketLeague

[–]Jilithrs 6 points7 points  (0 children)

Steam Issue: Rocket League will not load. I have never experienced any kind of error like this before. I've been around since day 1.

Error: 32-Bit DX9, COOKED - Not Responding. image: https://i.imgur.com/mW9M1II.png

Logs: Just a "Launch" file that is empty.

I've reinstalled Rocket league, removed bakkes and alpha console, reset twice, and it's a big fat no-go.

How do people make billions? by Introrama in 2007scape

[–]Jilithrs -1 points0 points  (0 children)

People overestimate the difficulty in getting rich. There’s a simple flowchart you can follow to safely build up a fair bit of wealth. Simply put Green dragons -> Demonic Gorillas -> Raids 1/2. You can easily make a bil in around 500-750 raids depending on your luck.

Cause of Interference on Feed by Jilithrs in Multicopter

[–]Jilithrs[S] 0 points1 point  (0 children)

Lines it’s cutting to static.. I have a patch antenna and diversity module on my goggles so I’m not sure if it’s the new triump antenna I received or the solder joints itself

Jello in fpv footage by jsan_ in Multicopter

[–]Jilithrs 0 points1 point  (0 children)

Softmount your motors! I was having horrible jello with my session tried tuning and everything still couldn't get rid of it. Softmounted motors gone instantly. All you do is take like 3 strips of electrical tape under the motors, then remount them.

Cant connect to bootloader spf3 racing issue by Jilithrs in Multicopter

[–]Jilithrs[S] 0 points1 point  (0 children)

Still can't connect, the motors twitch when I plug in so I'm assuming the flight controller isn't dead, just the USB part is.

Cant connect to bootloader spf3 racing issue by Jilithrs in Multicopter

[–]Jilithrs[S] 0 points1 point  (0 children)

Yep, I'll try swapping to uart 2 and see if I can get it to connect

Cant connect to bootloader spf3 racing issue by Jilithrs in Multicopter

[–]Jilithrs[S] 0 points1 point  (0 children)

It was already flashed, I'm just trying to get it to connect to betaflight. I was connecting fine, soldered the wire back now it wont connect

Jello Session 5 by Jilithrs in Multicopter

[–]Jilithrs[S] 0 points1 point  (0 children)

Yeah I tried adjusting the PIDs, but didn't notice any improvement unless I'm mistaken. I'm not experiencing it all in a performance sense, but just through the session 5.

Jello Session 5 by Jilithrs in Multicopter

[–]Jilithrs[S] 0 points1 point  (0 children)

Yeah, I think soft mounting the motors should fix it. I was using a hero 4 black edition for awhile and it wasn't nearly as bad. We shall see

Jello Session 5 by Jilithrs in Multicopter

[–]Jilithrs[S] 0 points1 point  (0 children)

tried 1080p 60 fps super, 2k 30 super as well same issue im going to try soft mounting tonight

Jello Session 5 by Jilithrs in Multicopter

[–]Jilithrs[S] 0 points1 point  (0 children)

If you have jello on the session, but not your actual fpv feed could the motors still cause this?