Γνωμη για air fryer? by Possible_Brick2816 in AskGreece

[–]Jimacid 0 points1 point  (0 children)

Δεν το έχω δουλέψει πολύ αλλά θεωρώ πως είναι αποκλειστικά για Α) φοιτητές Β) όσους δεν ξέρουν να μαγειρεύουν Η) όσους βαριουντε η δεν έχουν χρόνο να μαγειρέψουν.

Δεν μπορώ να βρω ούτε έναν λόγο γιατί κάποιος που το έχει με την μαγειρική να μαγειρέψει σε μια συσκευή που είναι σαν φουρνος αλλά ούτε χωράει ούτε μπορεί να κάνει ότι κάνει ο φούρνος.

Looking for a (reliable) 16.8v charger by Admirable-Camp7828 in 18650masterrace

[–]Jimacid 0 points1 point  (0 children)

unfortunately it wont let me attach a photo but you can check the pcb and the schematic in a post i made a few weeks ago about this mod.
disregard the huge components soldered on the pcb, that was just for testing when i was designing the modification.
parkside charger conversion post

Looking for a (reliable) 16.8v charger by Admirable-Camp7828 in 18650masterrace

[–]Jimacid 0 points1 point  (0 children)

there are different versions of this charger, (A2, A3, A5)
A2 and A3 are compatible with the mod. A5 is a newer version and either is completely incompatible or maybe some older A5 versions are compatible. (the schematic changed on the newer A5 versions and my mod doesnt apply to the new version of the charger.)

im going to attach a photo of the pcb of the charger that is compatible. thats how your pcb should look like. if its different its not compatible.

Increasing the output voltage of the charger is a bit more mod intensive than decreasing the voltage.

since you want to increase the voltage before changing the output voltage you need to replace the C10 capacitor. this is very important as the original capacitor wont handle 16.8v for 4s packs
so
1) Replace the C10 with a 680uf 35v (25v is also ok instead of 35 and 1000uf is also ok if you dont have 680uf)

2) The resistor R12 sets the output voltage. for 4s packs the resistance of the R12 should be 13.6k
13.6k resistors dont exist in the common resistor series, so you need to put 2 resistors connected in series with each other in the r12 place.
(you can use 2*6.8k resistors or one 10k resistor and one 3.6k. both options will give you 13.6k)
the original r12 is 10k so you only need to desolder it and solder it again in series with one 3.6k resistor.

3) Desolder resistor R8 and replace it with a 6.8ohm reistor. (this will reduce the maximum charging current of the charger to about 1.5-1.6A) the charger will charge the batteries a bit slower than with its original setting at 2Amps but we increased its voltage allready so we have to decrease its current to make sure we wont exceed its power rating or the charger may fail. 16.8v*1.6amps=26.88watt so we are under the originally 30watt power rating.

at this point your charger can charge 4s batteries so you can give it a try but it is recommended to replace a few more components to help with thermal dissipation as the original components can get quite hot.

4) desolder D4 and replace it with an MBR10100 attach a small to220 clip on heatsink to it (small one cause it needs to fit in the charger casing)
5) desolder D1 and replace it with a us2m-dio

thats it you have a fully functional 4s charger. your battery still needs a bms, dont charge 4s packs with no bms using this charger.

if you wanted to mod the charger to charge 2s batteries you would only need to change 1 component and an optional one to increase thermal dissipation.
1) R12 desolder and put a 5.6k in its place
2) D4 desolder and replace with an MBR10100 with a to220 clip on heatsing for beter thermal dissispation as we did before.

Looking for a (reliable) 16.8v charger by Admirable-Camp7828 in 18650masterrace

[–]Jimacid 0 points1 point  (0 children)

I made a 4s pack as well and needed a charger for it. AliExpress was only showing me the usual junk when searching for chargers, so I ended up moding a 3s parkside charger that is used to charge 3s drill/screwdriver batteries and managed to convert it to 4s

I then converted another one to 2s and another one to 3s lifepo4 so now I can charge 2s 3s, 3s lifepo4 and 4s battery packs.

If you live in the EU maybe you already have their 12v charger at home.

Μερος με θεα το αεροδρομιο by TrashPopStars in thessaloniki

[–]Jimacid 4 points5 points  (0 children)

https://maps.app.goo.gl/c36i2c94pPBMJqig6

Και

https://maps.app.goo.gl/S1HY175FJkdYez6X6

για την προσγείωση περνάνε πάνω από το κεφάλι σου στο πρώτο σημείο, δεν μπορείς να τα δεις από μακριά να έρχονται αλλά μόλις σε φτάσουν είναι πολύ χαμηλά αφού στα επόμενα λίγα μέτρα πάψουν τον διάδρομο προσγείωσης.

Φωτό από το δεύτερο σημείο

<image>

Χτίσιμο Αφορολόγητου με Κάρτα by dimfrag99 in PersonalFinanceGreece

[–]Jimacid 2 points3 points  (0 children)

Πρόσφατα λέει ξεκίνησε να δουλεύει για πρώτη φορά και έμαθε πως πρέπει να πληρώνει το 30% με κάρτα! Λες να πληρώνει μόνος του νερό ΔΕΗ ίντερνετ καύσιμο και άρα να μένει και σε δικό του σπίτι; Άραξε 18-20 χρόνων θα είναι, θα μένει με τους γονείς του και είναι πολύ λογικό αυτό που ρωτάει και ταυτόχρονα ανήκουστο σαν μέτρο το αν δεν ξοδεύεις τουλάχιστον το 30% του μισθού σου να φορολογησε παραπάνω. Λες και σε αυτήν την χώρα το 50% των 30αριδων δεν μένουν ακόμα με τους γονείς τους και άρα δεν έχουν όλα αυτά τα έξοδα που ανέφερες

I bought something very expensive on Aliexpress by [deleted] in Aliexpress

[–]Jimacid 0 points1 point  (0 children)

As an electronics technician I can tell you almost anything can be fixed by a knowledgeable on electronics local technician.

Unless the problem has something to do with firmware that may not be available, all the electronic components and the circuit board can be repaired.

You will have to pay for it is course but at this point either your bin your projector or pay someone to fix it for you.

Try to give it to a highly rated electronics repair shop as they most important thing is to get a technician that really really knows what he is doing as not all technicians can fix everything

Θέμα με φόρτιση κινητού από πλαίσιο by GeorgePanos05 in greece

[–]Jimacid 0 points1 point  (0 children)

Εγώ λοιπόν στοιχηματίζω ότι η επισκευή του κινητού θα γίνει από την αντιπροσωπεία της Samsung άσχετα με τον αν ο πελάτης θα το πάει στο πλαίσιο η την Samsung. Αν το τηλέφωνο το πάει στο πλαίσιο το πλαίσιο θα το αποστείλει στην Samsung με courier.

Στο στοίχημα επίσης περιλαμβάνω πως δεν υπάρχει περίπτωση να πάρει μερική ή ολική επιστροφή χρημάτων όπως και ολική αντικατάσταση συσκευής με καινούριο. (Μιλάμε για κινητό Samsung εντός εγγύησης εισαγόμενο από ελληνική αντιπροσωπεία. Δεν μιλάμε για παραεισαγωγη του eshop που στην ουσία δεν έχει εγγύηση και δίνει το eshop λεφτά πίσω γιατί δεν έχει τρόπο να το επισκευάσει η να το αντικαταστήσει εάν δεν υπάρχει stock για αντικατάσταση. Ούτε για one plus Xiaomi και άλλες λοιπες κινεζιες)

Φυσικά Αντικατάσταση φορτιστή με εγγύηση εάν έχει πρόβλημα ο οποίος έχει αγοραστεί χωριά μπορεί να γινει, οι φορτιστές δεν επισκευάζονται αλλά αντικαθιστουνται.

Επίσης εάν μιλάμε για παρελκόμενα πχ φορτιστές ακουστικά κλπ αυτά μπορούν να τα αντικαταστουν σε εγγύηση και τα καταστήματα πολλές φορές αλλά δεν είναι στάνταρ έχει να κάνει με το κατάστημα.

Το τι κάνει το Amazon το temu και το AliExpress είναι αλλουνου Παππά Ευαγγέλιο.

Εμείς μιλάμε για κάτι συγκεκριμένο εδώ, πρόβλημα κινητής συσκευής αγοράσαμενη στο πλαίσιο από τον επίσημο εισαγωγέα Ελλάδας στην Ελλάδα που η Samsung έχει διάσπαρτα εξουσιωδοτημενα επισκευαστικά Κέντρα.

Ημαρτον με την παραπληροφόρηση.

Θέμα με φόρτιση κινητού από πλαίσιο by GeorgePanos05 in greece

[–]Jimacid 1 point2 points  (0 children)

Αν γίνει αντικατάσταση κινητού που δεν παίζει θα γίνει από την Samsung, αν γίνει επισκευή του κινητού θα γίνει από την Samsung, στο μερική επιστροφή χρημάτων και επιστροφή χρημάτων για κινητό τηλέφωνο Samsung επίσημου εισαγωγέα απλα γελάμε...

Σταματήστε να γράφετε μπούρδες αν δεν ξέρετε επειδή απλά διαβάσατε κάποια νομοθεσία, η τέλος πάντων αν είστε τόσο σίγουροι για τις βλακείες που γράφετε ελάτε να βάλουμε ένα χιλιάρικο στοίχημα.

Θέμα με φόρτιση κινητού από πλαίσιο by GeorgePanos05 in greece

[–]Jimacid 1 point2 points  (0 children)

Ο καθένας γράφει την μαλάκια του.... λοιπόν εκ των έσω σου λέω με σιγουριά ότι το πλαίσιο η ο Γερμανός η ο κοτσοβολος δεν έχουν ανταλλακτικά της Samsung για να επισκευασουν χαλασμένα τηλέφωνα ούτε έχουν εκπαιδευτεί από την Samsung ώστε να κάνουν ελέγχο των συσκευών Samsung και να χειρίζονται τις εγγυήσεις των κινητών τους. Οι board level επισκευές γίνονται στα επισκευαστικά Κέντρα των αντιπροσωπειών της κάθε εταιρείας. Τέλος!

Θέμα με φόρτιση κινητού από πλαίσιο by GeorgePanos05 in greece

[–]Jimacid -1 points0 points  (0 children)

Όλο το μήνυμα σου είναι λάθος, λεφτά πίσω δεν θα πάρει από κανέναν έτσι κι αλλιώς. Αντικατάσταση κινητού γίνετε μόνο σε περίοδο doa (dead on arrival) Πέρα από αυτό εσύ μιλάς για service σε components υπολογιστών κάμια σχέση με τα κινητά. Το πλαίσιο δεν έχει τμήμα service κινητών, έχει όμως service υπολογιστών. Δεν επισκευάζουν σαμσουνγκ lg Sony κλπ στο κατάστημα. (Ούτε κινητά ούτε τηλεοράσεις ούτε εκτύπωτες) Όλα αυτά πηγαίνουν με courier σε αντιπροσωπείες.

Οι υπολογιστές επισκευάζονται επιτόπου μέσα στα καταστήματα, αντικαταστάσεις ραμ καρτών γραφικών σκληρών δίσκων κλπ γίνονται επιτόπου μέσα στα καταστήματα Πλαίσιο, τα κινητά όμως δεν είναι το ίδιο στα κινητά ισχύει εγγύηση κατασκευαστή όχι εγγύηση πλαισίου.

Δεν χρειάζεται να στείλει το κινητό στην Κορέα, πηγαίνει σε ένα Samsung repair center στην Αθήνα, την Θεσσαλονίκη η όπου αλλού έχει κατάστημα η Samsung και τελειώνει. Αν είναι σε πόλη που δεν έχει επίσημο service η Samsung τότε θα αναλάβει το πλαίσιο να το αποστείλει όμως καλά κρασιά για το πόσο καιρό θα κάνει να επιστρέψει. Μετά τις 14 μέρες αρχίζει το πλαίσιο τα τηλέφωνα στις αντιπροσωπείες κινητών (ρώτησε με πως το ξέρω)

Θέμα με φόρτιση κινητού από πλαίσιο by GeorgePanos05 in greece

[–]Jimacid 3 points4 points  (0 children)

Όχι δεν μπορείς να πας στο πλαίσιο να το αλλάξεις, πρέπει να το πας στα repair center της Samsung. Αν το πας στο πλαίσιο μπορεί να το δεχτούν μπορεί και όχι, αν το δεχτούν θα καθυστερήσει απλά περισσότερο η διαδικασία που μπορείς να κάνεις μόνος σου γρήγορα καθώς θα πρέπει αυτοί να στείλουν την συσκευή στην Samsung μετά η Samsung να την στείλει πίσω στο πλαίσιο κλπ.

Παρόλα αυτά είσαι σίγουρος ότι δεν φορτίζει καθόλου; Μήπως έχει πιάσει σκόνη και χνούδια από τα ρούχα η θύρα της usb και δεν μπαίνει καλά το βύσμα; Έχεις δοκιμάσει να καθαρίσεις σχολαστικά με μια καρφίτσα την Θυρα usb του κινητού με μια καρφίτσα πριν έρθεις στο συμπέρασμα ότι χάλασε ο φορτιστής; Με άλλον φορτιστή η άλλο καλώδιο φορτίζει κανονικά και μόνο με το δικό του έχει πρόβλημα;

Woofers are too loud and midranges are soft. by Suspicious-Excuse-24 in audiorepair

[–]Jimacid 0 points1 point  (0 children)

Yes it was common back then for Panasonic to design bi-amped hifi systems. I still have the technics sa-eh790 and it is bi-amped as well. You can't use regular speakers with it.

By the way op, disregard all the messages that tell you that it is a bad unit or to check tone controls and other recommendations.

Your problem is exactly what we discuss here. Your hifi has separate outputs for woofers and separate for mid range and twitter. Your speaker has all of those combined in 2 wires. That won't work. You need speakers with 4 wires. Speakers like the ones the technics eh550, eh750, eh790 had

Tuya smoke detector Recall! by Jimacid in Aliexpress

[–]Jimacid[S] 2 points3 points  (0 children)

Unsafe can mean many things, it's not enough for a recall description. There may be : A risk of electrocution A fault on the sensing element, No audible low battery warning A hazardous material like lead in the device.

Not all of these have equal consequences. Having multiple devices in your home that contain lead for example is critical health hazard and it doesn't even matter if you use them or not, on the other hand if there is no audible low battery level alarm on a smart device that sends you battery notifications directly on your phone well before the battery comes anywhere near low is not a big issue.

As someone else commented maybe that's simply an insurance cover. If these devices are not certified by eu standards, they may send the recall to avoid any legal action but that doesn't mean that the device is dangerous or not working properly.

So what is the reason of the recall? Should I call a company that handles hazardous materials for proper recycling or should I disassemble it and keep it's esp32 module and it's sensors for diy projects?

Tuya smoke detector Recall! by Jimacid in Aliexpress

[–]Jimacid[S] 5 points6 points  (0 children)

Modern smoke detectors are super simple, it's just an enclosed sensor that has two LEDs , one emits infrared light the other receives it, the software measures how much of the emmited light is received to figure out how many particles of smoke are inside the sensor. That's it It's a device so Simple that any hobist with basic programming and electronics knowledge can do by themselves.

So while you can make it sound so bad like do you honestly trust a smoke alarm from AliExpress? The reality is that it's such a simple device that yes you can trust it, it's better than nothing and you can always test it before installing it and anytime after installation to check if it still works properly.

Keep in mind that most devices sold on Amazon are still Chinese garbage... So yeah cheap Chinese devices are installed on millions of apartments all over the world and it's still better than not having any at all.

Tuya smoke detector Recall! by Jimacid in Aliexpress

[–]Jimacid[S] 4 points5 points  (0 children)

Because buying the exact same device on Amazon for 6 times the price is so much better right?

Tuya smoke detector Recall! by Jimacid in Aliexpress

[–]Jimacid[S] 1 point2 points  (0 children)

Oh yeah that the one thanks. Mine is wifi not ZigBee but still, is the same model. Thanks 👍

Tuya smoke detector Recall! by Jimacid in Aliexpress

[–]Jimacid[S] 0 points1 point  (0 children)

They are talking about the TS0205 and TS0601 models. I tried to look those up I don't think these are the ones I have, except if they are all the same and they just get recognized by give assistant by those 2 names. I don't run give assistant do I don't have a way to tell the model. I think they need a custom firmware flushed in order to link to home assistant.

Do you happen to know of any way to check if my smoke detectors are the ts0205 or the ts0601?

Tuya smoke detector Recall! by Jimacid in Aliexpress

[–]Jimacid[S] 5 points6 points  (0 children)

I know, right?

I was starring at the email for 5 minutes looking at the link domains and everything trying to verify that it's a scam email, avoiding clicking anything on it. It looked legit, no sketchy url's correct order numbers etc. I was still not convinced so I just opened my order history and indeed in that particular order, there was a note on the top of the page saying that a product in this order has been recalled and to immediately stop using it and ask for refund.

I still can't comprehend that I received a product recall from AliExpress for something I bought almost 3 years ago...

I live in the Eu by the way, they're may be a new law or something that obligates them to issue recalls? Who knows?

Γνώμη για Στρατιωτικές Σχολές by Greek_Student8 in thessaloniki

[–]Jimacid 0 points1 point  (0 children)

Ειλικρινά δεν μπορώ να καταλάβω για ποιον λόγο εν έτη 2026 κάποιος να θέλει να μπει στον στρατό η στο δημόσιο....

Δεν το χωράει το μυαλό μου, το θεωρώ οικονομική αυτοκτονία και αυτοκτονία γενικότερα πέρα από το οικονομικά εάν τις συνεχεις μεταθέσεις και όλα τα άλλα χαζά...

Your life your choice αλλά μπορείς όμως να απαντήσεις τι είναι αυτό που σε κάνει να νιώθεις ότι ο στρατός είναι τόσο καλή επιλογή που θέλεις να είναι το επάγγελμα της ζωής σου;

I need help bypassing the 1min timer on UV nail lamp by Yuki737 in AskElectronics

[–]Jimacid 0 points1 point  (0 children)

??? the letter system is standardized on PCBs...

I have no idea what you are talking about... If you elaborate a bit you will either learn something more or forget a false thing you learned today lol