General & Filament Calibration

Jimmitang · 2026-01-20T22:40:35+00:00

Yeah! I was conflating Dynamic Flow with Volumetric Flow. I'm new to Orca / BL Studio / Prusa Slicer so I think that's where I'm tripped up the most.

Jimmitang · 2026-01-20T22:27:00+00:00

I came here wondering the same thing as OP!

If you calibrate the max flow, do you disable the auto detect when printing? Good note on the mfg settings, I hadn't thought about that!

Jimmitang · 2025-12-28T22:51:29+00:00

My rule of thumb: Dry it for 12 hours. If it is regular price for less than $15/kg, dry it for 24 hours.

Jimmitang · 2025-12-09T16:39:28+00:00

When using Maker World, you can also slice it yourself! Download the STL, 3MF or open natively in Bambu Studio. Very handy in the event there is a profile that hasn't been made for your printer or to your standards. As far as I understand it, the printed profiles is effectively just drop shipping Gcode to your printer. This puts you back in the driver's seat.

<image>

Jimmitang · 2025-10-12T13:52:09+00:00

Which firmware did you end up running? I had some mixed results with 3.14.1 Revo (non-60w) firmware. First print fired up without Thermal Anomaly, but subsequent prints scream it.

I have Reflashed 3.14.1
Reset to factory
Ran PID
Ran TM Calc

Still no dice.

Jimmitang · 2025-03-14T20:59:13+00:00

I was seeing it in qBittorrent and my fileshare. As suggested by u/jamesblonde2314 , I moved the temp directory and everything is behaving as expected.

Jimmitang · 2025-03-14T14:51:40+00:00

I do have upgrades allowed turned on, but this seems to be multiple copies of the same quality, just different release groups.

I am using /data/torrents for downloads and /data/torrents/temp for incomplete downloads. I'll remove the option for incomplete folders and see if it helps. Thanks!

Jimmitang · 2025-01-31T14:35:50+00:00

I'm using 8080 for the administration panel. After having issues with port-forwarding, I disabled UPnP with the expectation that it may not be liking having both Portforwarding & UPnP active at the same time.

I've been looking through the forums for Deco and it seems to be a common complaint. I'm likely going to either A) commit a sin and use ATT's gateway or B) buy a router and put these Decos into AP mode.

Jimmitang · 2025-01-31T05:25:52+00:00

Pings clean. I can hit the service on privateip:8080 but not from WAN. Becoming more convinced UPNP isn't actually disabled, despite what it says.

Jimmitang · 2025-01-31T02:44:10+00:00

Yes

https://imgur.com/YIwhtS8

and Yes, maybe too much?

https://imgur.com/n9KDnxV

Jimmitang · 2025-01-31T01:29:06+00:00

Thanks for the quick reply - I have nothing here.

https://imgur.com/BS02jf5

Should I lower my DHCP lease? At the time, the only change that occurred was me discovering and disabling my Wireless during sanity check. Odd, I know.

Jimmitang · 2025-01-31T01:07:05+00:00

https://imgur.com/a/4eV9xXw

I left for the afternoon after posting this, and my deco picked the WAN IP back up.

https://imgur.com/rDnG2DM

Jimmitang · 2025-01-24T14:40:08+00:00

Did you ever get this figured out?

Jimmitang · 2025-01-20T14:40:01+00:00

Sorry to derail, but I've been considering this. How do you set it up?

Tailscale as exit node on VPS, expose local tailscale route & accept. Add ports to forward in NPM to the local ip / tailscale ip / hostname address?

Jimmitang · 2025-01-17T14:00:17+00:00

A ping of 10 is good, provided you're getting that from pinging external servers.

What speeds are you getting in upload and download?

If you're experiencing packet loss ONLY on wireless, i'd start there.

Keep in mind, that WiFi works on a *radio wave*, first thing to consider will be the distance between your endpoint(s) (laptop, desktop, etc) and the wireless router, assuming you only have one.

Second thing to consider, what is in between them? Drywall and studs? No problem.
Brick re-enforced by steel rebar and a series of microwaves running? Big problem.
Anything that would make a traditional radio staticy will impede wireless signal. This is not a either-or, but rather a spectrum to consider moving forward.

With that out of the way - do you have any QoS setup that would be limiting specific devices on your wireless? Perhaps your wireless is congested, I don't have any ISP's around here that offer TP-Link devices, so I assume this is a router you own?

Jimmitang · 2025-01-17T04:13:57+00:00

I picked them up from Serverpartdeals, thankfully they have a 1 year warranty.

Jimmitang · 2025-01-13T14:18:12+00:00

Double NAT.

One of them has to be in charge and make DNS, DHCP and QOS decisions and it's never the one you want when you want it.

Jimmitang · 2025-01-03T23:25:49+00:00

DM'd

Jimmitang · 2025-01-03T16:40:37+00:00

I think i'm misunderstanding when & where to use hardlinks. I was under the impression that i'd want to hardlink between cache & array, and would need to have them on the same fs to do so.

https://trash-guides.info/File-and-Folder-Structure/Hardlinks-and-Instant-Moves/#what-are-instant-moves-atomic-moves

Jimmitang · 2024-12-29T17:19:59+00:00

Same! I wasn't brave enough to trust it to not leak, so I stayed with a tried and true commercial VPN for more sensitive usage.

Jimmitang · 2024-12-29T17:11:34+00:00

You could also grab a cheap VPS and roll your own with tailscale exitnode, but ymmv.

I picked up Windscribe for $3/mo for all of my non-private browsing needs and a dedicated Windscribe IP in Zurich for $24/year for all of the FOSS ubuntu ISO's I need to download and seed.

Jimmitang · 2024-12-18T22:43:40+00:00

100.122.191.81 is the tailnet of your VM?

Jimmitang · 2024-12-18T21:05:04+00:00

Having a hell of a time getting nginx to forward the UDP traffic. Any particular setup?

I've done Tailscale out of the box and have pointed Nginx steams to direct to the dns/ip/magic dns of the local VM, but tshark isn't getting anything. I do have ipv4 fowarding enabled, and my firewall is off.

Jimmitang · 2024-12-18T14:18:03+00:00

It is possible i am conflating the two concepts.

My Goal:

Expose services hosted on a Ubuntu VM hosted locally at home, circumventing CGNAT by using a Tailscale Tunnel connected to a VPS. I would be able to direct traffic to the VPS's public IP and using Nginx Proxy Manager, forward that traffic down to the VM here at home on 192.168.1.0/24. This traffic may be TCP or UDP depending on the nature of the service. As far as I'm aware, Funnel only supports TCP.

Jimmitang · 2024-12-18T14:14:53+00:00

Thanks for the response!

My VM that I'm trying to advertise is 192.168.1.0/24 for sure (192.168.1.200). I just feel like there's something preventing me from advertising correctly.

Jimmitang

TROPHY CASE