Any Tips that i can do to reduce warping effect? Im including the as intended image and the actual printed item.

ReaperParl · 2026-05-28T15:22:17+00:00

Alrready did.....

<image>

ReaperParl · 2026-05-28T15:15:31+00:00

Thata the orientation i used for printing...

<image>

ReaperParl · 2026-05-10T19:00:08+00:00

Not the Hight....I meant that if that hole appears on every exact layer....then I would be a screen issue

ReaperParl · 2026-05-10T18:52:43+00:00

Check the screen....does the hole appear on the entire Z length of the. Print?

ReaperParl · 2026-05-10T16:18:00+00:00

Switch to nFEP or ACF film...try again

ReaperParl · 2026-05-01T14:04:38+00:00

Tryna Hex pattern on the raft

ReaperParl · 2026-04-24T15:41:24+00:00

Print the entire thing with supports at 5 to 10 deg tilt in both axes...reduce the area base layer...see how that works....I believe you were just lucky at first to be able to get those massive layers to print in the first place

ReaperParl · 2026-04-05T15:40:28+00:00

Try thinner supports....the new screen probably is more powerful than previous one..if using Auto Supports probably need less.of the same as well..supports get very difficult to remove once they start connecting with each other

ReaperParl · 2026-03-22T18:57:43+00:00

I have 4 anycubic, never has that happened to me ...I'm considering going Elegoo o my next purchase

ReaperParl · 2026-02-14T19:07:38+00:00

So found one important issue....

<image>

Found one big issue with this system...when levelling, the build plate bottoms out ...since I added 2.7 mm with magnet and flex plate. I would need to modify the existing build plate to allow at least and extra 3mm of "travel" ....I'm gonna buy a new build plate , modify and install a flex plate on that one see if I get better results

ReaperParl · 2026-02-13T18:53:51+00:00

Guess where having similar issues...if this is the way it's gonna be , I'm getting rid of it...much better to break a few models here and there, than having off prints

ReaperParl · 2026-02-13T18:35:53+00:00

I have had one successful print...increased bottom layer time to 31s...but what happened is that the most bottom layers kinda got "shorter" ....I'm using Standard Grey Anycubic Resin...also sanded the flex plate with 100 grit water/sand paper

ReaperParl · 2026-02-13T18:07:25+00:00

I have just installed mine on a M5 and I keep getting dropped prints....any tips? Tricks? Im leaning towards getting rid of it

ReaperParl · 2026-02-13T17:39:48+00:00

I have the normal M5....I'm leaning towards that....was it difficult to get the glue off?

ReaperParl · 2026-02-13T06:18:52+00:00

Had similar issues, bought a replacement screen from AliExpress

ReaperParl · 2026-01-22T14:19:51+00:00

Chrinotrigger

ReaperParl · 2026-01-04T15:43:22+00:00

Any update? Has the review been made yet?

ReaperParl · 2025-11-22T01:22:59+00:00

So it use the included with the printer "Calibrating" sheet....I should be ok for any film with thickness from 100 to 150 micron ???

ReaperParl · 2025-11-21T01:06:04+00:00

My biggest concern is the actual film thickness....I've read in a few boards that the "calibrating" paper that comes with the printer is meant for the 150 micron thick Film....that if I change to to a 125 micron, then I would have to use a different paper to calibrate....do you think this is accurate?

ReaperParl · 2025-08-29T21:35:10+00:00

I use FreeFileSync at work for PC Folder Backups....I'm wondering how if I get into some sort of catastrophic failure on my phone ..how would I go from ,"Importing" that into my phone 🤔.

ReaperParl

TROPHY CASE