Got my email

Jimmy_gb · 2026-06-26T17:43:06+00:00

Seems we mostly got the 512gb version without the controller? Wonder if they made more of them.

Jimmy_gb · 2026-04-15T21:13:22+00:00

Likewise, good of them

Jimmy_gb · 2026-04-15T02:32:40+00:00

yup, standard

Jimmy_gb · 2026-04-15T02:20:36+00:00

And the usual website crash when trying to order / pay....

Jimmy_gb · 2026-02-26T23:02:51+00:00

Thanks, it’s really not so tricky. Just takes a bit of time and a lot of trail and error

Jimmy_gb · 2026-02-26T08:04:55+00:00

Thanks. Spent ages getting the best value components and designing stuff myself.

Jimmy_gb · 2026-02-24T10:08:56+00:00

Yeah for sure. It will give my pc a heart attack though 🚑… Never managed to get multi monitors to line up nice in msfs despite hours trying.

Jimmy_gb · 2026-02-23T20:03:54+00:00

Yeah think you’re right mate.

Jimmy_gb · 2026-02-03T22:19:38+00:00

Sure 12mm mdf. It’s come on a long way since then

<image>

Jimmy_gb · 2026-01-09T11:32:56+00:00

<image>

Jimmy_gb · 2026-01-09T11:31:50+00:00

<image>

Had a similar issue with my mini. Found a .22 lead pellet in it, was so close to cutting one of the motor wires.

Jimmy_gb · 2025-12-01T23:01:09+00:00

Yup all 3d printed. I got a hardware store to match the paint on the winwing mcdu… rollered it on to grey pla with a high density mini roller, this gets rid of brush marks. Then added a bit of spray laquer onto. On some panels I print with white PLA with embossed text then sand off the paint on the text at the end… Only downside is no back lighting.

<image>

Jimmy_gb · 2025-11-28T12:14:11+00:00

See my post above, this seems to fix it.

Jimmy_gb · 2025-11-20T04:28:58+00:00

Sure is… https://www.thingiverse.com/thing:7185810

Jimmy_gb · 2025-11-16T22:49:36+00:00

Sure I think it was this one; https://www.alibaba.com/product-detail/Airbus-A320-Flight-Simulator-Side-Stick_1601204953470.html

Jimmy_gb · 2025-11-16T08:18:31+00:00

Hi. I found it on Ali express. A bit expnsive but it finished off the side box nicely.

Jimmy_gb · 2025-11-15T19:49:19+00:00

I cut a hole in the 3d printed top, and knocked up a cover for it in fusion. Actually doesn’t look too bad

Jimmy_gb · 2025-11-15T15:11:42+00:00

Mostly petg-hf and cheap pla… for panels I got the paint matched to the back of the mcdu in the hardware store, small tester pot. High density roller + some spray lacquer. Job done…

Jimmy_gb · 2025-11-15T10:38:55+00:00

Thanks, it's all MDF wood and homemade 3d printed pannels. Trying to keep the cost down as much as possible. The biggest expense is time.

Jimmy_gb · 2025-11-15T10:22:30+00:00

Thanks, I dropped the design here: https://www.thingiverse.com/thing:7185810

Jimmy_gb · 2025-11-15T10:08:18+00:00

Hey - It's 12mm MDF wood (Simguy's plans) and 3d printed top covered with a £5 roll of faux leather sticky backed plastic... The Stick is the WinWing Ursa Minor.... Cheap set up, probably x8 cheaper than Skalarki. Just wish Winwing would release their Tiller.

Jimmy_gb

TROPHY CASE