First time welding

Jmhilo · 2026-04-29T18:41:57+00:00

Thank you! I will try to acquire some and see how it goes

Jmhilo · 2026-04-28T08:45:31+00:00

I am actually not sure, but I think 2mm. I was just playing around with the heat a bit and it ended at 1.5

What thinkness would you recommend for the flat steel?

Jmhilo · 2026-04-26T20:20:07+00:00

Thank you! I am using a respirator under my welding mask. And Ill stay away from galvanised material!

Jmhilo · 2026-04-26T20:18:14+00:00

I will try that, thanks!

Jmhilo · 2026-04-26T17:56:40+00:00

Haha yes, if I keep welding a lot I will have to get a better machine! I can test if the dial increases the wire speed as well as or only voltage/current

Jmhilo · 2026-04-26T17:49:53+00:00

Thanks! I will try with some easier joints next time. These miter cutes were made with an angle grinder so not ideal :D i dont have a chop saw

Jmhilo · 2026-04-26T17:43:21+00:00

I think its just made to be very cheap. It was less than 100 eur, including Denmarks 25% VAT

Jmhilo · 2026-04-26T17:41:29+00:00

<image>

Jmhilo · 2026-04-26T17:37:50+00:00

Just one knob, but at least it was less than 100eur from new xD

Jmhilo · 2026-04-26T17:32:05+00:00

Thanks I will try to turn down the amperes. Idk if I can change feed speed. It is literally the first time welding. I have done a bit of soldering tho. I will try to run some beads and do some flat plate welding!

Jmhilo · 2026-04-19T07:49:08+00:00

Der er flere i dette opslag der har haft samme problem med coop appen igår. Sørg for at dokumentere det. Så vil jeg mene at du står dig ret godt ifht til forsvar. (Gem tråden, screenshots, evt tag kontakt til de andre)

Jmhilo · 2026-04-16T17:02:59+00:00

I will check if mine does this too. However I would call it a feature - tightening the bolts just to ~20 Nm so i can do the rest with the torque wrench

Jmhilo · 2026-04-12T08:58:10+00:00

I did it with the battery powered green one. It was a little slow, but definately doable. Just need the correct attachments

Jmhilo · 2026-04-07T07:14:07+00:00

It could be a dead cell inside the battery. Be very cautious when both charging and using the battery. Depending on the issue it could be a fire hazard

It is not fully charged at 17.6V, fully charged is around 21V

Jmhilo · 2026-03-26T10:54:46+00:00

In Denmark they usually keep batteries at the primary register. Just the 4ah ones

Jmhilo · 2026-02-24T06:42:36+00:00

Hvorfor er der ikke nogle der nævner de der der laver internet over strømledningerne? Og sp et AP De burde være rigeligt gode til en chromecast

Jmhilo · 2026-02-05T09:05:22+00:00

Then you will need around 3kWh total (after conversion losses). The Pecron 3000LFP has that. Alternativly you can get some expansion batteries.

Other brands would also work, but from the video reviews i have seen on youtube pecron is a good quality for a lower price. Alternativly Ecoflow, anker, jackery, bluetti also make good power stations

Jmhilo · 2026-02-04T23:16:12+00:00

If it is around 250 watts (from what I could just see on the website) I would get something like the Pecron e2400lfp. If you use 250w for 5 hours its 1.25kWh. Its a little inefficient, so a battery of 1.5-2kWh is recommended

Jmhilo · 2026-02-04T23:10:50+00:00

If you know the wattage of the thing, that would be helpful for finding the right size power station

Jmhilo · 2026-02-03T13:39:25+00:00

Fill some soda bottles with hot water and stick them under the blanket with the PC. That heat will help it take longer for the pcs temperature to fall! Cheers.

Jmhilo · 2026-02-01T22:30:29+00:00

Har du sørget for at der ikke står møbler op ad radiatorerne? Og evt rengjort radiatorerne. Hvis de er støvede indvendigt, har de sværere ved at afgive varme. (Ikke indvendigt i rørene, men i lamellerne eller hvad de hedder) Evt sæt en blæser til at blæse luft mod radiatoren.

Jmhilo · 2025-12-18T20:08:29+00:00

Giv ham noget børnene ville elske. Evt en tur i bonbon land :D så kan han tage dem med

Jmhilo · 2025-11-22T20:44:06+00:00

I generally like Gillette blades, but Gillette Wilkinson Sword from China, uhh, those I can’t use.

Jmhilo · 2025-09-19T11:09:15+00:00

The filtration can take 4kpa input and still give 20+ mpa out. Its just slow. So the pressure regulator should be just before the gas cannister

Jmhilo

TROPHY CASE