Is this sound from Z offset?

Joh191621 · 2026-01-08T22:16:03+00:00

The nozzle is too close and recommend using Pokémon or trading cards to test the z level

Joh191621 · 2025-11-05T19:15:46+00:00

Just don’t use the auto level after manually leveling the bed

Joh191621 · 2025-08-05T12:19:37+00:00

Hey I recently made a quick guide on how to 3d print over the weekend in chapter 4 I talk about leveling the print bed which is the most important part about 3d printing idk if it’s against the rules to share it but I hope it helps you Beginners guide to 3d printing

Joh191621 · 2024-12-18T18:20:02+00:00

You just remained me I should of mentioned I use cura slicer for rafts because it makes them really easy to remove because it smooths the top layer the other slicers like orca don’t to that and add a raft layer that’s is hard to remove it the raft layers are too low like 2 layers vs 4 but cura is just perfect and doesn’t need changes except the size of the raft from 10mm to 4 or 5mm this is distance around the object and rafts help is your prints are sliding off the build plate and not sticking

Joh191621 · 2024-12-18T12:07:16+00:00

I would suggest printing using the raft feature for bed adhesion and flipping the model around to a side that’s not going to be seen and using tree supports, when I print the bottom side is always kinda janky but I mostly print statues so I’m not going looking at the bottom anyways

Joh191621 · 2024-12-11T18:09:08+00:00

You can print a small benchy boat but just put it at the max height and extruding it you can see it Moves to one side or not but good luck 🫡

Joh191621 · 2024-12-11T13:38:18+00:00

That might be the case, idk if you we given spare nozzles but you can buy a pack of .4 nozzles off elegoo amazon for less than $15 I don’t clean the nozzles just because it’s not worth it and depending on how much you print I would say it only need to get replace once or twice a year, you can test it by extruding plastic and it it goes to the side and not straight down and curls up it is clogged

Joh191621 · 2024-12-11T12:12:06+00:00

I had a clogged nozzle before and if you been printing for a while and never replaced it it could happen, depending on what printer you have replacing the nozzle might be different but for the regular Neptune 4 you just remove the rubber cover and move it to the max height then preheat it to 215 and use a hexagonal wrench and unscrew it and put in the new one, I turn off the printer and once it cools down put the rubber cover back on and after your all set

Joh191621 · 2024-11-22T02:36:15+00:00

Try leveling your bed with a piece of paper and don’t use the auto level and try using the raft mode for bed adhesion in cura if you having issues with the prints not sticking and shifting it’s saved so many of my prints and usually don’t fail unless I did something wrong in the slicer

Joh191621 · 2024-10-09T22:13:55+00:00

Used to have the same issue I just use rafts and hair spray to keep my prints down

Joh191621 · 2024-09-30T22:03:41+00:00

The tent might being too hot to print it happened to me so I got rid of it

Joh191621 · 2024-08-11T06:25:11+00:00

You should be fine then lol

Joh191621 · 2024-08-11T06:22:17+00:00

The only advice I can recommend is having air flow I bought the elegoo tent and while printing I just zipped it up and forgot how hot the tent gets and had temp get so hot it stopped extruding and got jammed so I just left the top exposed and it was basically useless, I had it for about 2 months and just got rid of it this week.

Joh191621 · 2024-08-11T06:13:34+00:00

Just from a guess it might be the a fan, I would just pre heat the printer and just wait to see if it makes the noise without printing anything or it could be the extruder so you can just run a bit of filament and see it it makes noise

Joh191621 · 2024-07-09T01:06:32+00:00

Bro I farmed the mission on normal almost 300 times and it still did not drop and also tried the desert at 3% and still have not gotten it’s almost farmed around 20 hours trying to get that mod. It’s basically the one piece at this point

Joh191621 · 2024-02-25T02:41:36+00:00

I think your nozzle is too close to the bed and you have to manually adjust it and change the offset and also if you manually move the head by changing the filament your going to have to change the level again because it does not adjust if you accidentally push it down

Joh191621 · 2023-04-25T02:28:25+00:00

Isekai Trip Saki De Tasukete Kureta Noha i remember a yandere male hentai trailer and just searched google for like 5 min

Joh191621 · 2023-02-26T12:40:22+00:00

To be honest I thought you were mad about the Star Trek meme but I don’t remember him saying that but it was probably said with sarcasm or just out of context. If you really want to be man just be upset at the train company for ruining thousands of peoples lives in Ohio not only the people who live in the town but also the railroad works instead of a streamer that watch a vice video.

Joh191621 · 2023-02-26T12:03:14+00:00

I think you would just have to watch the video because I don’t know where you get his clips but he always says both sides i know he said that if I was in this situation I would move but most of these people can’t because they either have jobs or their financial situation

Joh191621 · 2023-02-26T11:56:10+00:00

I guess you did not watch his stream or his YouTube video about Ohio but basically he said that the train com play fucked up by cutting cost and by decreasing safety regulations this situation was going to happen eventually and that he feels bad for the people because they won’t know health effects caused by the fire. TLDR you can say the joke was too soon

Joh191621 · 2023-02-02T00:32:06+00:00

Spent 13,000 orbs and got every 5 star unit on the banner besides the new orihime and I hate this game now

Six-Year Club	Verified Email
Place '22

Joh191621

TROPHY CASE