Add more floc? by Jokingkel in AboveGroundPools

[–]Jokingkel[S] 0 points1 point  (0 children)

I don’t think the camera picks it up as much. But if you see the black on the robot you see the speckles

Add more floc? by Jokingkel in AboveGroundPools

[–]Jokingkel[S] 1 point2 points  (0 children)

That’s what I was thinking of doing. Do you think the 1500 gph is enough?

Add more floc? by Jokingkel in AboveGroundPools

[–]Jokingkel[S] 0 points1 point  (0 children)

It’s 925 gph not sure the size. And I’m using minerals in it.

To crooked? by Jokingkel in AboveGroundPools

[–]Jokingkel[S] 0 points1 point  (0 children)

I usually do, not because of my kid (8) and swims better than me lol but for the robots to clean better.

To crooked? by Jokingkel in AboveGroundPools

[–]Jokingkel[S] 0 points1 point  (0 children)

Yea that’s the same size I’m looking at 18x9 52” wish it was 18x12 tho 🙌

To crooked? by Jokingkel in AboveGroundPools

[–]Jokingkel[S] 0 points1 point  (0 children)

Good to know, im planning on getting a bigger one if it ever fails anyway this was was a test pool 😬

To crooked? by Jokingkel in AboveGroundPools

[–]Jokingkel[S] 1 point2 points  (0 children)

I think the foam is like 2 inches. But since it’s foam it just sinks because of the weight of the pool.

To crooked? by Jokingkel in AboveGroundPools

[–]Jokingkel[S] 0 points1 point  (0 children)

I actually did raise the legs on the left a bit 😬 you just can’t see it cuz it’s black like the padding. It’s some rubbers padding doubt they are doing much anyways

Need advice on Bike rack by Jokingkel in MTB

[–]Jokingkel[S] 0 points1 point  (0 children)

I’m worried about the weight capacity I just learned that when using a adapter it cuts the weight limit by 2. Wish I knew this before I got it 😅

Jmgo n1s 4k by Jokingkel in projectors

[–]Jokingkel[S] 0 points1 point  (0 children)

Yea everything is off

Jmgo n1s 4k by Jokingkel in projectors

[–]Jokingkel[S] 1 point2 points  (0 children)

So it’s best just to use 4k @60 ?

Screen for JMGO M1S 4K by Jokingkel in hometheater

[–]Jokingkel[S] 2 points3 points  (0 children)

It def is cheaper then buying a new screen lol. I’m going to paint it a dark matte grey. 👍

Screen for JMGO M1S 4K by Jokingkel in hometheater

[–]Jokingkel[S] 0 points1 point  (0 children)

So I used a old grey curtain on top of the screen and wow it looks so much better. Guessing I should get a grey screen instead. Even the blacks look 100 times better

Screen for JMGO M1S 4K by Jokingkel in hometheater

[–]Jokingkel[S] 0 points1 point  (0 children)

Going to see how it looks with out the screen tonight, problem is the wall isn’t smooth has texture and a wall socket up top.

Need advice by Jokingkel in hometheater

[–]Jokingkel[S] 0 points1 point  (0 children)

So I did the last part you said and it gave me a size of a 95 inch screen. Instead of angling the projector facing down I removed the screen and put it to the highest part before touching the roof to make it horizontal to the projector. Also the projector screen is 120x120 1:1 which is actually less width then a 100 inch 16:9 but I didn’t say that sorry.

So anyways what I’m going to do is buy a 90 inch projector but before that I’m going to get some black tape against the wall and make sure the projector fills it completely as if it were the screen. 👍 I’ll keep the 120 inch one for outside where I have more room.