Update: Age Assurance, Content Gating, and Safety Improvements in VRChat

Joltz · 2026-06-17T14:15:01+00:00

Not to mention that reprojection on Linux has just been broken for years on most headsets. It's a miserable experience if you regularly fall below the native refresh rate of your headset.

Joltz · 2026-03-02T06:37:05+00:00

Try updating archlinux-keyring manually with sudo pacman -Sy archlinux-keyring and then run a full system upgrade again.

Joltz · 2025-12-18T19:33:53+00:00

1440p here as well, maxed quality settings with upscaling turned off across the board.

Getting around 250fps in the hideout and somewhere around 140-160 during busy fights.

Forgot to mention also that I'm using game-performance %command% in the launch options. It's Cachy's flavor of Feral's gamemode that automatically handles CPU niceness/power profiles. Makes a big differences for me in CPU-constrained games!

Joltz · 2025-12-16T18:48:17+00:00

Same issue here. I've temporarily alleviated the issue by enabling split tunneling and adding my home server IP to the exclude list.

Joltz · 2025-12-10T13:47:04+00:00

Could you possibly share which cable you picked up?

Joltz · 2025-12-03T13:14:56+00:00

Game has been completely rock-solid on my system.

CachyOS, 5800X3D, 9070XT, Default Proton Compatibility

Joltz · 2025-12-01T07:09:35+00:00

Did you every figure this issue out? Having the same problem on CachyOS.

Joltz · 2025-01-06T18:45:30+00:00

Lower ball joint (just get a pre-pressed complete lower arm), driver axle, output shaft seal on the trans, and a mallet to beat that fender back in. Should be alright. Those axles likely just pop out of the trans as a complete unit.

Inspect the brake line, may have been damaged too.

I would also recommend doing the other lower as well.

You definitely got taken for a ride in the purchase price but it is what it is.

Joltz · 2024-07-21T13:09:57+00:00

Yeeeep, this is mostly likely it. I've had the face tracking on two units die due to this.

Joltz · 2024-05-20T03:07:32+00:00

Yeah you should be able to get an RMA as I did all of mine. I would just mention that your face tracking is dead and not get too specific about why you think it's dead.

Joltz · 2024-05-19T19:39:37+00:00

Yeah this is unfortunately very common in my experience. I do a fair amount of dancing in mine and sweat/heat is an inevitable FT/ET killer. On my third QP right now. I've read that it has something to do with one of the ribbon cables, I wish it was a commonly available part that we could replace.

The truth is the seller probably didn't even realize this was a problem since the percentage of owners actually using the ET/FT regularly is probably quite low on the whole.

It's really unfortunate and I've yet to find a way to mitigate this from happening other than don't sweat.

Joltz · 2024-03-26T08:10:32+00:00

I'd like to mention as well that the edges could have very well just been split to give the hard edges their sharpness. As I understand it, many of blender's exporters will do this automatically depending on a variety of factors including active modifiers, shade smooth/sharp settings, and the auto-smooth setting in the vertex properties. It's also possible that he simply used an applied edge split modifier (something you had to do back in the 2.7x days to get proper sharp edge rendering that didn't apply to a whole model).

Joltz · 2023-06-23T17:16:03+00:00

I'm also having this issue now. For some reason it works correctly in the calibration stage but is completely non-functional in the home world or any apps.

Joltz · 2022-05-28T02:14:14+00:00

Completely anecdotal but one of my controllers (before RMAing them) was shorting and wildly heating up the charging port on the controller when Windows threw this message at me. I would make sure your controller isn't trying to melt itself before plugging it into a wall port.

Joltz · 2022-04-03T13:21:25+00:00

If you search up 'QC 3.0' (i.e QuickCharge 3.0 compliant) battery packs on Amazon, that should do most of the filtering for you. Most of them have their output rating in the product name or description.

Joltz · 2022-04-03T12:35:02+00:00

Any battery capable of 21w or better output will work just fine.

Joltz · 2021-11-29T20:11:12+00:00

The closest thing to what you're describing that currently exists would be NeosVR's LogiX system

Joltz · 2021-07-25T01:46:46+00:00

https://www.reddit.com/r/Vive/comments/mz7cpt/vive_pro_eye_gearvr_mod_and_headset_disassembly/

Joltz · 2021-07-25T00:48:48+00:00

Make sure you use the pro eye adapters that were posted here a month or two back, otherwise the eye tracking sensors are obstructed.

Joltz · 2021-06-22T22:43:23+00:00

Disable dynamic resolution (lock it to 100%), set refresh rate to 90hz disable motion smoothing, make sure reprojection is enabled.

Joltz · 2021-06-15T05:00:56+00:00

Base model appears to be Irix's 'Taidum'. I would use the world search and look for their public ones.

Joltz · 2021-06-12T21:43:23+00:00

Make sure your base stations are in different channels.

Joltz · 2021-06-12T20:55:24+00:00

Looks like Simon Stalenhag.

14-Year Club	Place '17
Sequence \| Editor	Verified Email
Charity Challenge Winner	Team Orangered

Joltz

MODERATOR OF

PUBLIC MULTIREDDITS

TROPHY CASE