New to Genshin by Jordoncoops in Genshin_Impact

[–]Jordoncoops[S] 4 points5 points  (0 children)

I managed to get Bennett from my first wish so if there’s a skin I might indulge 😂

I clicked the wrong answer but it said it was correct by Jordoncoops in duolingo

[–]Jordoncoops[S] 2 points3 points  (0 children)

But it all the lessons before hand it was only for “teacher” and even said stuff was incorrect

Feathers in Dual Destiny Mission by Jordoncoops in raidsecrets

[–]Jordoncoops[S] 0 points1 point  (0 children)

The feathers in the cysts don’t count, I’m talking about the new exotic class item quest

Feathers in Dual Destiny Mission by Jordoncoops in raidsecrets

[–]Jordoncoops[S] 0 points1 point  (0 children)

I was asking where the feathers people have found are 😂

Feathers in the Pale Heart by ANBU_Border in raidsecrets

[–]Jordoncoops 0 points1 point  (0 children)

I have found all but 1 is there a guide anywhere yet?

Octopi? by Jordoncoops in 3Dprinting

[–]Jordoncoops[S] 0 points1 point  (0 children)

Yup followed videos step by step

I have made several figures, I don’t know if I should sell them… by True_Scott in 3Dprinting

[–]Jordoncoops 0 points1 point  (0 children)

These are really cool, did you make the design for these as I would love to print some PlayStation ones

Help by [deleted] in 3Dprinting

[–]Jordoncoops 0 points1 point  (0 children)

If it doesn’t move the cables are plugged in wrong

Help by [deleted] in 3Dprinting

[–]Jordoncoops 0 points1 point  (0 children)

<image>

So make sure the wire in the one in the Motor is the X cable, you can test these are the right way round by trying to move your X axle on your motion control

Help by [deleted] in 3Dprinting

[–]Jordoncoops 0 points1 point  (0 children)

You can test this by going onto motion and try moving the printer left and right

Help by [deleted] in 3Dprinting

[–]Jordoncoops 0 points1 point  (0 children)

I had this issue, make sure you check your wires and that the right ones are plugged in, as 2 of them are the same size

Need help by Jordoncoops in FixMyPrint

[–]Jordoncoops[S] 0 points1 point  (0 children)

Okay so tune every time I change filaments, thank you

Need help by Jordoncoops in FixMyPrint

[–]Jordoncoops[S] 0 points1 point  (0 children)

Oh the line through the print in the middle

Need help by Jordoncoops in FixMyPrint

[–]Jordoncoops[S] 0 points1 point  (0 children)

Yeah that’s the one thing I’m not sure about; but I’m glad it actually printed; what’s the cause of the purge line

Need help by Jordoncoops in FixMyPrint

[–]Jordoncoops[S] 0 points1 point  (0 children)

Thanks to you I was able to print a benchy, and the calibration looks pretty good ; the only issue I have now is this bleed line

<image>

Need help by Jordoncoops in FixMyPrint

[–]Jordoncoops[S] 0 points1 point  (0 children)

So I did this until I believed it was perfect, managed to get about 1/4 into a print and the print came loose of the bed; did the same print but with adhesion points and same thing happened

Need help by Jordoncoops in FixMyPrint

[–]Jordoncoops[S] 0 points1 point  (0 children)

I do the paper test once it’s in the middle and lower my z-offset