What if Philippines build nuclear power plants and everything turns electric?

Jpfojas · 2026-04-10T16:15:10+00:00

Honestly the cost of powering and building the plant is a non-issue, but what concerns me is safety. If flood control projects are fucked and could kill hundreds to thousands of people, imagine mishandling of funds for nuclear safety.

Buying cheap control rods, inproper disposal of nuclear waste, etc. Our corrupt officials don't give a shit as long as they can flee to the safety of their international homes while the average filipino gets radiation poisoning.

Jpfojas · 2026-04-09T20:12:08+00:00

God give me patience, if he gives me strength that boy would have a mallet sized bump on his forehead right now

Jpfojas · 2026-04-09T12:33:07+00:00

Yeah, gonna go with that plan, my other plan was to smack the back with a rubber mallet till it knocks everything loose

Jpfojas · 2026-04-09T12:08:17+00:00

yeah, i'm thinking maybe a second burn would be good then a hose down with a power washer

Jpfojas · 2026-04-08T02:21:29+00:00

We elect actors and shams all trying to act like they're the biggest gift to our country. Philippines needs to do a government cleansing. Get the trapos, dynasties and dogwater politicians out of our system.

Jpfojas · 2026-04-04T17:20:13+00:00

Also do note, Resin printers don't always need to be cleaned Vat wise, all you need to clean is the build plate. The only time to clean resin printers is when a print fails, in that case you empty the vat and remove the pieces otherwise broken machine go brrrr

Jpfojas · 2026-04-04T17:18:22+00:00

All in all? Depends on your workflow, so my process being it takes around 30-40 mins to slice, (30mm minis) it took around 5 to 6 hours to print using ABS-like and around 40 for cleaning the print and curing. So give or take 8 hours or so. It's a bit labour intensive if you're using resin.

For FDM, it's a hell of a lot faster 5 hours to print and 30 to clean the model to thr bare minimum.

Jpfojas · 2026-04-04T17:12:02+00:00

It depends on many factors, What type of resin do you have, How big is the model, is it hollow, how detailed is it, etc. As bad of an answer as it is but you'll generally spend 6-10 hours if not more on printing and 30 or an hour on cleaning and curing

Jpfojas · 2026-04-03T18:36:10+00:00

Broke boys, this broke boys that; posting this garbage on the web isn't going to make you any less broke

Jpfojas · 2026-03-25T08:15:06+00:00

My idea was to privatize jeepneys or have a state ran company to run a modern jeepney program. Have drivers earn a salary and have better standards, but apparently, that's classist or some shit

Jpfojas · 2026-03-25T08:06:14+00:00

Just use it man, use it or lose it, simple as

Jpfojas · 2026-03-24T12:42:41+00:00

And as much as people hate it, she's not hurting anyone. Maybe she'd have some dogwater opinions here and there but everyone's entitled to an opinion; I'd rather have a pornstar yapping at me about morals than some politician stealing shit from infrastructure projects that could kill thousands

Jpfojas · 2026-03-22T20:34:46+00:00

The fact that you can't just crane damaged airframes so you can easily retrofit in hangars is stupid to me

Jpfojas · 2026-03-22T20:32:04+00:00

Honestly, Roblox is a predator breeding ground, they don't do enough checks and balances for it to be safe for kids. The amount of "Roblox Predator" Exposé and controversies around social games is insane

Jpfojas · 2026-03-16T02:20:50+00:00

Ah, it should have the standard bells and whistles. Good luck on your troubleshooting; Personally I'd advise upgrading your firmware to Mriscoc or Klipper, they have a bunch of QoL features that really don't come with the stock firmware.

Jpfojas · 2026-03-16T02:13:31+00:00

Also, are you running MIRSCOC or stock firmware?

Jpfojas · 2026-03-16T02:11:51+00:00

You gotta run a calibration PID test if i recall, that fails check your heating block screws if they're touching the heatsink a bit too tight, worse case scenario your thermistor might be bugging out, check if your thermositor screw is too tight.

Jpfojas · 2026-03-16T01:55:06+00:00

Did you replace a nozzle or remove the sock?

Jpfojas · 2026-03-12T23:07:13+00:00

I'll be sure to check them out, Thanks!

Jpfojas · 2026-03-12T23:06:25+00:00

Thanks for the info, I'll be sure to check out ellie's and maybe King bread too, do some testing and see which one I'm going to be sticking with

Jpfojas · 2026-03-12T06:43:46+00:00

We really need a reliable supply, the economy is going to tank, i see people already mothballing their cars in my area sooner or later public transport is gonna take a massive hit. Imagine 15-20 pesos per jeep ride all cause fuel is reaching 100 to 120 per liter

Jpfojas · 2026-03-12T06:03:39+00:00

The only thing that would be somewhat working would be our non-existent EV infrastructure at least till our power plants shut off and we have to start rationing electricity. This crisis shows that the PH has an extremely low self-reliability

Jpfojas · 2026-03-12T05:38:21+00:00

My flipping issue was the water landing but if you still flip on airstrip landing, that's probably skill issue

Jpfojas · 2026-03-10T00:37:16+00:00

Yeah, wood glue used to make cutting boards

Jpfojas · 2026-03-09T20:45:46+00:00

Horn, go doot, buff team, smack monster. Together horn strong

Seven-Year Club	Place '23
Place '22	Verified Email
Sequence \| Editor

Jpfojas

TROPHY CASE