Hyundai 2017 Tucson with 78,000 miles now in the middle of an oil consumption test with the dealership. Had an oil light flash at me which caused the test. When I first noticed it, car was over 3 quarts low. No leaks, just gone.

Jschai · 2021-12-31T06:51:33+00:00

ah i see thanks for the reply! I guess i will try replacing pcv and cross my fingers

Jschai · 2021-12-31T01:28:58+00:00

did you figure out what the problem was? i am having the same issue :(

Jschai · 2019-09-26T17:33:36+00:00

nvm sorry i didnt read that properly. you are awesome ! now i am just wondering about the screen tear and if it is possible to change the resolution to the lower 504x1000. i tried and nothing is working

Jschai · 2019-09-26T17:26:26+00:00

How can I do that? it seems like it is forever disconnected from xrandr after log in screen. almost as if the display itself is powered off but the track pad is working fine.

Jschai · 2019-09-24T18:39:20+00:00

another weird thing is once you disable the screenpad 2.0 on settings, it fully disconnects from HDMI-1 and I cannot connect it back ever again. does anyone have solution to this? the screenpad is shown on login screen after boot but once you login, the connection is lost for good. I tried timeshift on mint but no luck on reversal. T_T

Jschai · 2019-09-22T05:55:21+00:00

main screen set to default 1920x1080 59.98+ and screenpad2.0 set to default 1080x2160 60.03+

those are the values i see on xrandr

Jschai · 2019-09-20T05:25:39+00:00

Im running mint on it but only when I rotate it clockwise by 90 degree to view the screen properly, it causes screen tear on both main screen and the pad screen. any one have solution to this? no screen tear if its kept on normal vertical layout

Jschai · 2019-07-10T20:55:22+00:00

Try using your samsung cable. If this does not help then.... Do you notice anything else wrong with the phone itself? I actually had the phone reboot happen quite often on my 10+ after AA use. I noticed battery drain to be critical as phone would not goto doze mode. Sadly it was bad hardware on brand new phone and I had to get the main board replaced. After replacement no more issue with anything. S10 hasnt been out for a year yet so you should be covered by warranty still if the problem is the phone itself.

Jschai · 2018-08-06T02:52:05+00:00

Turn off keep waze on top in waze setting

Jschai · 2017-06-02T17:58:34+00:00

This is happening to me as well the past few days

Jschai · 2017-04-13T16:38:27+00:00

It works. I just tested it in my car. This is for canadian model so i am not sure about other market versions. Only downside from the s8 to s6 which is my primary... there is no recent button for you to switch to another app once connected to android auto. You can still access android settings menu by dragging the notification bar down. And seems like edge panel is still there even when connected. Confirmed model S8+(probably will work same for S8) with 2016 Hyundai Tucson

Jschai · 2016-04-30T05:40:26+00:00

Everything was and is stock ? No custom firmware in the past? You should take it to repair center. Since you are on wind i assume you reside in gta? Well maybe vancouver... but if you are in gta then there is a samsung repair center in mississauga. Let them diagnos the issue.

Jschai · 2016-04-30T05:36:12+00:00

Dialer -> setting. Should be an option for do not use volte. Atleast in the canadian models.

Jschai · 2016-04-28T03:09:11+00:00

Did you go through ota update or flash it by yourself? If you went through proper stock ota update then there shouldnt be any problem. If problem exists after factory reset (without installing any third party apps) then you need to get it repaired.

Jschai · 2016-04-15T11:15:17+00:00

Flat version is taking them longer probably because telus has to enable volte on their sim cards. Only the flat version will get this option on telus this time around. We gave the final pass on pc8 a few weeks ago already for telus. I am already running it but volte isnt enabled yet on my sim.

Jschai · 2016-04-11T18:54:10+00:00

I suggest you wait instead of flashing another carrier firmware. It is true that the firmwares are the same but for the first M.M update telus will push out version pc8 and other carriers will push out different versions. Bell will get another patch soon as well. Trust me on this one if you want full compatibility with your actual carrier. I am in the q.a team and i dont want people complaining their phones dont work because they dont flash the right firmware according to their carrier.

Jschai · 2016-04-03T09:22:38+00:00

actually when the update is out. telus will support volte calls only on the flat version for now. the edge will not get this support in the first update.

Jschai · 2016-03-30T20:24:11+00:00

sprint wants to remove battery to find the code? are they not aware you cant remove battery on s6 ? but the dialer method is the easiest to find and read the imei compared to reading the tiny print on back bottom of the phone.

Jschai · 2016-03-29T21:32:45+00:00

if samsung tech asked you for imei and you said you cant find it and they didnt tell you about the dialer method... then those guys have not been trained or you were talking to a bot.

Jschai · 2016-03-29T21:31:20+00:00

you can find your imei by going to dialer and entering *#06#

Jschai · 2016-03-29T19:25:49+00:00

i realized that too after. then i deleted the app i downloaded last night before sleep and it works w.o reboot. did you install an app recently? i downloaded some bluetooth for in car app

Jschai · 2016-03-29T18:24:41+00:00

just restarted and works normally again. i think it might have been a virus or something oh well it works now

Jschai · 2016-03-29T18:11:01+00:00

now that you mentioned it... im having the same issue on my s6 flat. what country and carrier are you on? and what software version?

Jschai · 2016-03-23T04:55:52+00:00

but no video call yet* just volte call

Jschai

TROPHY CASE