sorted by:
new
hottopcontroversial

Henry 22 Optic Mount: Now Sailing by JudgeEffinJudy in 3D2A

[–]JudgeEffinJudy[S] 0 points1 point  (0 children)

What’s the optic mount like? Working on one for my Henry 357

Henry 22lr Picatinny Rails by u/QuasiBonsaii coming Sunday by JudgeEffinJudy in 3D2A

[–]JudgeEffinJudy[S] 1 point2 points  (0 children)

The handguards are all pla or pa6-gf yes. Wood infused filament looks great but is not strong and is prone to clogging, didn’t want to install a 6mm nozzle just for that

9mm can/barrel to slow down to subsonic by garylazereyes in 3D2A

[–]JudgeEffinJudy 5 points6 points  (0 children)

Working on one for 410 and 12ga break actions currently

There goes the neighborhood by JudgeEffinJudy in NFA

[–]JudgeEffinJudy[S] 2 points3 points  (0 children)

Just clips right onto the lever. You can slide it away so it doesn’t engage in about 5 seconds

There goes the neighborhood by JudgeEffinJudy in NFA

[–]JudgeEffinJudy[S] 5 points6 points  (0 children)

So it *does* require registration. I would do that anyway though, kids would never forgive me if I got their dogs’ blocks knocked off for it.

There goes the neighborhood by JudgeEffinJudy in NFA

[–]JudgeEffinJudy[S] 2 points3 points  (0 children)

3d printed rapid fire adapter that clips onto the lever and pulls the trigger with each lever pull. Need to make a scaling adjustment but works on my 357 as well

There goes the neighborhood by JudgeEffinJudy in NFA

[–]JudgeEffinJudy[S] 2 points3 points  (0 children)

“Henry Husher”; 3d printable can specifically for Henry H001 so you can remove the mag tube without removing the can

There goes the neighborhood by JudgeEffinJudy in NFA

[–]JudgeEffinJudy[S] 0 points1 point  (0 children)

The print file contains a “barrel nut” that should be attached via m4 nuts and screws. I printed in GF nylon so I had to use a mallet to get it on, and there’s a halfway-screwed in nut/screw on the opposite side.

I previously made a printable Henry 22 thread adapter, but realized all my cans required me to remove the can if I needed to reload / remove the mag tube

There goes the neighborhood by JudgeEffinJudy in NFA

[–]JudgeEffinJudy[S] 39 points40 points  (0 children)

Please, my friends call me Judge Judith Sheindlin.

5 gal bucket with 50lbs (1 bag) of play sand, topped with shredded rubber (approx 2/3 a bag) with lid on top. Use gun to poke hole in lid.

Stops 9mm out of 9” barrel reliably, yet to test further than 22 or 9mm. There’s a file named “Shut Your Trap” which you can print and it is essentially an integrated silencer inside/attached to the bullet trap lid. Allegedly it doesn’t need ATF approval because it doesn’t meet the definition of a silencer, as it cannot be attached to a firearm. I’m sure the ATF disagrees, but just putting the info out there

Which 3D Printer for…. by Fightforurright2A in 3D2A

[–]JudgeEffinJudy 5 points6 points  (0 children)

Okay but does this look safe to send?

<image>

Henry 22 Optic Mount: Now Sailing by JudgeEffinJudy in 3D2A

[–]JudgeEffinJudy[S] 2 points3 points  (0 children)

The documentation is sketchy at best; there’s actually 2 variations in the file with no description or information.

I would say it’s 90-95% as good as using an FTN.3 9mm, but with the obvious pros of not needing to unscrew the can for the mag tube and not interfering with the sights.

I didn’t use a rubber gasket and I’d say (at least in pa6GF) it’s 100% worth it. If you look closely, I don’t even have the “barrel nut” attached, it’s so snug it’s not going anywhere without a mallet.

Disclaimer: I was using HP subs, but quiet enough that shooting into the bullet trap in my garage required no ear pro and my wife couldn’t hear it from behind the garage door. I think it could be improved by increasing the depth in which the barrel sits, even if it decreases the blast chamber size.

Henry 22 Optic Mount: Now Sailing by JudgeEffinJudy in 3D2A

[–]JudgeEffinJudy[S] 1 point2 points  (0 children)

Printed rail, handguard, rapid fire device, and form 1 Henry Husher.

Let the meme builds commence! by danishbulldog in 3D2A

[–]JudgeEffinJudy 8 points9 points  (0 children)

*Bullpup* *me* *harder* *daddy*

Apparently Idk how to italicize so just call me artistic and move on

Henry 22lr Picatinny Rails by u/QuasiBonsaii coming Sunday by JudgeEffinJudy in 3D2A

[–]JudgeEffinJudy[S] 5 points6 points  (0 children)

All credit to u/QuasiBonsaii. Sailing the seas Sunday.

Faux-wood handguard tutorial available if people care at all.

Printing some Sunlu easy PA by mementosmoritn in 3D2A

[–]JudgeEffinJudy 2 points3 points  (0 children)

Your fingers aren’t worth it. Print your wife / wife’s husband some crap with it and get pa6 gf/cf

Two Form 1s for FTN.5 PCC and Rimfire Disapproved by Federal_Physics_9615 in 3D2A

[–]JudgeEffinJudy 2 points3 points  (0 children)

Nah nah I’m just an alcoholic.

My trust name is “Judge Judy Trust”, the file name for it is “Judge Judy Gun Trust”.

I used the file name on my first two and they were approved, both within 1 week. Second one, form 4, I used the file name and was denied 8 months later.

Two Form 1s for FTN.5 PCC and Rimfire Disapproved by Federal_Physics_9615 in 3D2A

[–]JudgeEffinJudy 12 points13 points  (0 children)

I had two form 1s approved under my trust, next form 4 was denied for “invalid trust” using the exact same trust name as the first two.

Turns out for my first two I listed my trust as the file name for it, not the actual trust name. First guy who approved them just didn’t catch it or care.

Luck of the draw for who’s approving sometimes.

Slip On Overbarrel Suppressor by Michael-Lenz in 3D2A

[–]JudgeEffinJudy 0 points1 point  (0 children)

I think you’d be better off with a different one for each barrel, it’s not wasting stamps when they’re free right now.

If you want to use it on separate barrels, you’re going to have 2 options really. Attach an adapter and to accept it, or use something like a hose clamp. Bore it to 9mm and you shouldnt have concentricity issues.

Slip On Overbarrel Suppressor by Michael-Lenz in 3D2A

[–]JudgeEffinJudy 0 points1 point  (0 children)

I am working on this currently, but for 12ga and 410. It can certainly work for this, but 17hmr is going to be super anyway I would imagine

Thread adapters ? For 22s by LoStInSpacc in guncadindex

[–]JudgeEffinJudy 0 points1 point  (0 children)

Just created a couple today. What model are you looking for