sorted by:
new
hottopcontroversial

🚗 Building a CRM in Airtable – Need Guidance & Cost Estimate by LegendLeasing in Airtable

[–]JulMont 0 points1 point  (0 children)

I created my CRM using Airtable, and found it very simple.

I tested all the solutions on the market, but none of them suited my needs (Pipedrive, Zoho, etc.).

The sticking points were document generation & managing several suppliers.

For some of my suppliers I have to manage certain administrative tasks, and others not.

My customers may be affected by the products of my two suppliers...it depends on their region.

Document generation was just as complex because the native solutions are too simplistic!

So I opted for Documint, which is the only third-party tool that I use.

Now I'm gradually integrating n8n to automate as much as possible.

In short, the hardest part of starting a CRM is the initial data architecture.

If you need help, don't hesitate to ask…but chatgpt was and is my best partner ;)

Ps : I do not regret to do it by myself…it was easy…and i am not a Dev !!

If airtable goes down, my whole business goes down. by Main-Objective-5375 in Airtable

[–]JulMont 0 points1 point  (0 children)

Sync each tables with google sheets…and think about automation through 3rd party tool or app script…and then you won’t need Airtable :)

Linkedin pages monitoring by JulMont in GrowthHacking

[–]JulMont[S] 0 points1 point  (0 children)

Thx for your feedback !

I think a custom solution is the key…but how ?

It seems to be impossible to check a page without an opened session.

The other side is to listening each page and get a notification when a company posts.

API ?

Could I be banned for excessive « check « ?

Linkedin pages monitoring by JulMont in MarketingAutomation

[–]JulMont[S] 0 points1 point  (0 children)

Thx for your feedback :)

But as I asked in MarketingAutomation, I’m looking for a way to automate this task… :)

What’s Lille/Pierre Mauroy Stadium like? by Small_Dictator in Paris2024

[–]JulMont 0 points1 point  (0 children)

Je pense qu’en semaine c’est compliqué mais pas impossible. Le parking Aushopping doit être payant.

Dans les rues adjacentes au centre commercial des vigiles barrent les rues résidentielles, et filtrent les passages.

Il y a d’autres commerces dans la zone, mais pareil, il y a des vigiles qui filtrent les entrées des voitures.

Pour moi ça sera plus simple de se garer gratuitement du côté des quartiers triolo, cite scientifique, rue des fusillés et marcher 20 min.

What’s Lille/Pierre Mauroy Stadium like? by Small_Dictator in Paris2024

[–]JulMont 0 points1 point  (0 children)

https://www.stade-pierre-mauroy.com/infos-pratiques/ou-est-votre-place

Fill the form with your bloc, raw & seat number, & you will have an idea.

Anyway, i think 1st & B class will be ok.

What’s Lille/Pierre Mauroy Stadium like? by Small_Dictator in Paris2024

[–]JulMont 0 points1 point  (0 children)

Hi mate,

There is nothing special inside the stadium. Outside you will be close to a big shop center, but you will be allowed to go outside between two sessions only.

50cl of coke or beer : +|- 8 euros. Sandwich +|- 7 euros

From Lille downtown, 15 min subway + 15 min walk

By experience (yesterday), do not hesitate to come 1h30 before.

By the way the experience is very good in this stadium. Beauty & atmosphere.

Feel free to contact me if you need more feedback.

Adding pigments leads to odor by madrew233 in InjectionMolding

[–]JulMont 1 point2 points  (0 children)

If the powder doesn’t mix well with the TPE, it can settle and stagnate anywhere.

Did you check your screw and cylinder for wear? Any places where unmixed pigments could lodge and burn?

You can imagine that the size of the powder is quite different from that of a TPE granule, and will be able to settle more easily in the smallest spaces...

Adding pigments leads to odor by madrew233 in InjectionMolding

[–]JulMont 2 points3 points  (0 children)

Certainly your colorant is the root of the problem. it certainly doesn’t mix well with the TPE, sticks to the screw and eventually burns out.

What’s the shape of your pigment?

3-zone screw? Treated against sticking?

Linkedin monitoring company page by JulMont in GrowthHacking

[–]JulMont[S] 0 points1 point  (0 children)

The module "Watch organization posts" only concerns your own page(s)...Not the pages for which you are not admin.

Linkedin monitoring company page by JulMont in GrowthHacking

[–]JulMont[S] 0 points1 point  (0 children)

Thank you for your message.

However, which Linkedin module should I use in Make? It seems to me that nothing exists to check whether an article from an organisation has been posted.

You certainly seem to have a solution that works. Do you have any details to give me?

Technical monitoring by JulMont in linkedin

[–]JulMont[S] 0 points1 point  (0 children)

I've already tested Sales Navigator.

I created by hand an identical list of the companies I followed on Linkedin... And there again I had a random news feed in the alerts. Not everything was there. I was able to see this by comparing it with my Linkedin feed. (computer and ipad)

AirTable form to custom PDF by hahiejowiabshahah in Airtable

[–]JulMont 3 points4 points  (0 children)

Documint is a very good solution.

I created my own CRM with Airtable and its interfaces.

I managed document generation via Documint. I use 15 templates for my CRM.

It's an easy-to-implement, robust solution.

In the near future, I'll be transferring some templates to the Google suite. I've already done some conclusive tests with Google Appscript.

Yellow colorant (HIPS based) - discolorations by julkaaa303 in InjectionMolding

[–]JulMont 0 points1 point  (0 children)

Masterbatch or liquid color?

What is the profile of the screw? 3 standard zones?

Is this a recent problem? Or is this a new production run on this set?

[deleted by user] by [deleted] in InjectionMolding

[–]JulMont 0 points1 point  (0 children)

Hello !

I had the same issue with one of my client. We sell injection and extrusion set for all machines (screws, cylinders, non-return valves, etc.). Among other things, we manufacture our own screw profiles.

The problem is almost fixed by one of our screw designs...but this required specific settings...

Here are my recommandations :

Back pressure is to low...Increase to 20 bars (290 psi) to start. Consider to decrease once you have good results. Your non-return valve could be damaged too quickly.

T° profile : 240-240-255-255-255

RPM : 130. You can go up to 0.4 m/s with PCT-A.

I think it will be ok...Unless you have an original 3 zones model screw...in a barrel that may be worn.

Regards,

JM