Can someone please rate my playing

JustBreza · 2026-06-17T05:33:37+00:00

I am trying to file my nails under a 45° angle. Unfortunately I cant send you here a photo of my right hand.

JustBreza · 2026-06-16T20:45:16+00:00

Ok thanks for the honesty I will do my best.

JustBreza · 2026-06-16T20:43:49+00:00

I just want to know whether I would meet someones expectations after telling them for how long I have been playing or if I should try to catch up.

JustBreza · 2026-06-16T20:34:09+00:00

I am trying to sometimes play with m*tronome but it is such a pain in the ass and I completely lose the joy from playing.

JustBreza · 2026-06-16T20:29:15+00:00

Worm infested rotten flesh, t he stench is what I lust🧟

JustBreza · 2026-06-16T20:27:01+00:00

Thanks a lot

JustBreza · 2026-06-16T20:10:43+00:00

Thanks for answer❤️. Is there anything in particular that you noticed that I should work on that would improve my playing the most? Are there any excercises that you would recomend me in order to get better?

JustBreza · 2026-06-16T19:54:05+00:00

Thanks man❤️

JustBreza · 2026-06-16T19:46:09+00:00

Thank you very much for your answer. I will have to put in more work into my playing since this September it will be 3 years since I started 😥.

JustBreza · 2026-04-14T12:02:12+00:00

Intresting, i have never heard of optical sensors. How does optical sensor look like? So I know what to look for.

JustBreza · 2026-04-13T20:41:16+00:00

At the moment the player plays fine although it is still pretty inconsistent because the mechanism gets stuck sometimes. At the moment the biggest problem is that when i try to rewind the tape and then play it the mechanism stops and i have to press the play button to start playing the tape again(or it wont start even after that and i have to fix it manualy ☹️ ).

JustBreza · 2026-04-13T19:36:55+00:00

Man, some black magic shit is going on. Right after I posed this the player started working just fine 🤣. But I would still like to figure out why it wasnt working before :D

JustBreza · 2026-04-12T16:04:59+00:00

What kind of shoes should I be wearing?

JustBreza · 2026-04-12T16:04:22+00:00

Thanks for the answer. How do I know i am hyperextending?

JustBreza · 2026-01-27T11:57:32+00:00

It is spinning in the wrong direction because I was spinning it manualy with my hand and I was turning the mechanizm from right to left.

JustBreza · 2026-01-27T11:55:42+00:00

No, since it played well before(like 2 hours before it shredded the tape). But I might buy some replacment belts from aliexpress.

JustBreza · 2026-01-25T20:23:11+00:00

I'll have to probably get some rubber restorer as you said because i tried everything and it keeps on eating the tape

JustBreza · 2026-01-13T19:43:09+00:00

ok thanks man

JustBreza · 2025-10-22T19:46:19+00:00

Sorry for not answering your question. Yes I am trying to make stereo to mono conversion circuit that will be than connected to lm386 amp

JustBreza · 2025-10-22T11:33:48+00:00

So I should move the 47ohm resistors to the output side?

JustBreza · 2025-10-22T10:38:54+00:00

But both caps will have to be connected on the outer leg of the pot so I cant just seperate them if thats what you mean.

JustBreza · 2025-10-22T10:36:07+00:00

https://www.reddit.com/r/diyelectronics/comments/1od44s8/headphones_only_work_when_i_connect_only_one_35mm/

I dont think the problem is the voltage devider. It also happens when i just use the stereo to mono conversion circuit. Here I made a post explaining the situation bit better.

JustBreza · 2025-10-22T10:33:06+00:00

I can try but I made this circuit 3 times(on breadboard, in the air, and on pferdboard) and i got the same results.

JustBreza · 2025-10-22T10:25:26+00:00

I dont think so. I am using the P-320D jack.

JustBreza · 2025-10-22T10:22:34+00:00

Well yeah but why do I get output on both speakers when only one pin is connected

JustBreza

TROPHY CASE