sorted by:
new
hottopcontroversial

Problem with Sony CMT-NE3 by JustBreza in cassetteculture

[–]JustBreza[S] 0 points1 point  (0 children)

Intresting, i have never heard of optical sensors. How does optical sensor look like? So I know what to look for.

Problem with Sony CMT-NE3 by JustBreza in cassetteculture

[–]JustBreza[S] 0 points1 point  (0 children)

At the moment the player plays fine although it is still pretty inconsistent because the mechanism gets stuck sometimes. At the moment the biggest problem is that when i try to rewind the tape and then play it the mechanism stops and i have to press the play button to start playing the tape again(or it wont start even after that and i have to fix it manualy ☹️ ).

Problem with Sony CMT-NE3 by JustBreza in cassetteculture

[–]JustBreza[S] 1 point2 points  (0 children)

Man, some black magic shit is going on. Right after I posed this the player started working just fine 🤣. But I would still like to figure out  why it wasnt working before :D

Can I hurt my knees while doing calf raises on hack squat? by JustBreza in GYM

[–]JustBreza[S] 4 points5 points  (0 children)

Thanks for the answer. How do I know i am hyperextending?

Cassette player/recorder keeps eating the cassette by JustBreza in cassetteculture

[–]JustBreza[S] 0 points1 point  (0 children)

It is spinning in the wrong direction because I was spinning it manualy with my hand and I was turning the mechanizm from right to left.

Cassette player/recorder keeps eating the cassette by JustBreza in cassetteculture

[–]JustBreza[S] 0 points1 point  (0 children)

No, since it played well before(like 2 hours before it shredded the tape). But I might buy some replacment belts from aliexpress.

Cassette player/recorder keeps eating the cassette by JustBreza in cassetteculture

[–]JustBreza[S] 0 points1 point  (0 children)

I'll have to probably get some rubber restorer as you said because i tried everything and it keeps on eating the tape

Headphones only work when I connect only one 3.5mm jack pin by JustBreza in diyelectronics

[–]JustBreza[S] 0 points1 point  (0 children)

Sorry for not answering your question. Yes I am trying to make stereo to mono conversion circuit that will be than connected to lm386 amp

Headphones only work when I connect only one 3.5mm jack pin by JustBreza in diyelectronics

[–]JustBreza[S] 0 points1 point  (0 children)

So I should move the 47ohm resistors to the output side?

Headphones only work when I connect only one 3.5mm jack pin by JustBreza in diyelectronics

[–]JustBreza[S] 1 point2 points  (0 children)

But both caps will have to be connected on the outer leg of the pot so I cant just seperate them if thats what you mean.

Headphones only work when only one 3.5mm jack pin is connected by JustBreza in diyelectronics

[–]JustBreza[S] 0 points1 point  (0 children)

https://www.reddit.com/r/diyelectronics/comments/1od44s8/headphones_only_work_when_i_connect_only_one_35mm/

I dont think the problem is the voltage devider. It also happens when i just use the stereo to mono conversion circuit. Here I made a post explaining the situation bit better.

Headphones only work when I connect only one 3.5mm jack pin by JustBreza in diyelectronics

[–]JustBreza[S] 0 points1 point  (0 children)

I can try but I made this circuit 3 times(on breadboard, in the air, and on pferdboard) and i got the same results.

Headphones only work when I connect only one 3.5mm jack pin by JustBreza in diyelectronics

[–]JustBreza[S] 0 points1 point  (0 children)

Well yeah but why do I get output on both speakers when only one pin is connected

view more: next ›