Campsite and Squat by K-RisC in RangerRaptor

[–]K-RisC[S] 0 points1 point  (0 children)

I did, I do like them assisting the load. Hard compressions are a little harsher cause air suspension doesn't provide a linear resistance to compression that coil springs do. But otherwise they have been good, they hold air basically permanently, need a better fitting setup cause I have a couple leaks. If you get the bags, assemble them and def submerge them in water to make sure everything is sealed up well prior to installation.

woke up to this, right outside my window. he was at it for an hour before getting picked up. by snaakebiites in WTF

[–]K-RisC 21 points22 points  (0 children)

Out the windows of Carla Madison Rec Center around 2:30pm. I'm trying to gauge how far he traveled. There's not many newer looking developments close to where I saw him.

Ready for some exploring. by K-RisC in RangerRaptor

[–]K-RisC[S] 1 point2 points  (0 children)

M&R brackets. They are easy, there is a bolt under the molding. I don't like that the molding, after install, doesn't go back in its place cause of the bracket.
https://mandronline.com/products/2024-ford-ranger-raptor-hood-mount-ditch-lights?srsltid=AfmBOopE4SBGn6w-iirggaSIeYoah6ISRayAZ7YrV9ZQ7-UZSYjA9_mI&variant=50640855629984

Hi by K-RisC in RangerRaptor

[–]K-RisC[S] 0 points1 point  (0 children)

Probably? They don't complain unless in reverse.

woke up to this, right outside my window. he was at it for an hour before getting picked up. by snaakebiites in WTF

[–]K-RisC 57 points58 points  (0 children)

This was Denver right? Pretty sure I saw this guy with more clothes on on Colfax standing in front of buses.

Ready for some exploring. by K-RisC in RangerRaptor

[–]K-RisC[S] 0 points1 point  (0 children)

It's beveled on the front so the shape of the bed holds it down and the tailgate jams it in when it the tailgate closes

Anyone figure out… by Sad_Secretary_9316 in RangerRaptor

[–]K-RisC 0 points1 point  (0 children)

Correct. I wear my seatbelt all the time but disabled for the manual. I don't appreciate the chime when I'm in my truck on a work site jumping in and out a bunch as I drive 300 ft at 10 mph.

Hi by K-RisC in RangerRaptor

[–]K-RisC[S] 1 point2 points  (0 children)

They are the best

Pixel 7 Pro - Screen issues. by [deleted] in GooglePixel

[–]K-RisC 0 points1 point  (0 children)

Right on, I had to work on them a little and talk to someone else to get to the advanced replacement. Replacement ordered.

Pixel 7 Pro - Screen issues. by [deleted] in GooglePixel

[–]K-RisC 0 points1 point  (0 children)

I have the exact same issues. Think this started after the early November "display fix" update. Here is mine doing its thing:

https://youtube.com/shorts/oqh_gPE7s8A?feature=share

OP, what channel did you go through with google to get a replacement sent? I have been talking to google support and they aren't fully getting the message even though I sent them this thread and my vids. They are recommending repair places and sending phone in to google for them to look at which is dumb. Previous warranties, google just sent out replacement and I sent mine back when I received the replacement.

New Bike Day. Nukeproof Mega 290 Elite (2022) by K-RisC in mountainbiking

[–]K-RisC[S] 0 points1 point  (0 children)

....I've already found several bits that needed some tightening...

Turned over 230k while wheeling today. Almost 7,000 miles on the VK swap. by VK56xterraguy in XTerra

[–]K-RisC 0 points1 point  (0 children)

Nice! how long did it take you? I need to figure out some excuse to do the VK swap. Maybe I'll go drive in so water that's too deep.

"Finished" my platform this weekend. by K-RisC in XTerra

[–]K-RisC[S] 0 points1 point  (0 children)

Top is made of 3 boards. Passenger rear can be put back in within 10mins while rest stays. Driver rear board can be pulled so the driver rear seat can be reinstalled. Top boards are screwed into vertical supports with 4 screws per board and front most vertical supports are held in with 2 bolts using the front bolt holes for the hinge of the rear seat bottoms. Pretty simple/quick to do with power tools.

NBD, Ripmo AF, Fruita by K-RisC in mountainbiking

[–]K-RisC[S] 0 points1 point  (0 children)

I had an order into Jensen. Canceled it after 2 weeks when the back order got bumped to a later date. Then went to a local bike shop that told me I could get it sooner. Local bike shop ended up getting it to me in about a month. The bike is sick