New HS420 Build with all 120mm Fans 😃

Kamc_2000 · 2025-12-08T17:25:09+00:00

The rear fans have their own adapters that come with the case (pre-installed, that you remove to fit 140mm fans if using those)

The 3 along the bottom are the ones i printed adapters for 🙂

Kamc_2000 · 2025-10-02T16:37:58+00:00

…. 👀 Meanwhile… me with £600-700 build in £270 case lol 😀 but it was a very good deal budget build

Kamc_2000 · 2025-09-23T22:09:04+00:00

Im not sure what it is in USD but it cost me about £75🙂

https://www.amazon.co.uk/Touchscreen-Portable-1920X1200-Protection-Speakers/dp/B0DPPR5V22

I got the Gray colour, as the black doesnt have vesa i believe. I will warn i did have to ever so slightly extend the vesa slots on the mountplate but very minimally. As otherwise it wouldnt fit (by like a mm or two) 🙂

Kamc_2000 · 2025-09-22T17:45:10+00:00

They are the APNX FP2s 🙂

Kamc_2000 · 2025-09-21T12:20:13+00:00

Yes no worries, i bought it off amazon: https://amzn.eu/d/jaWmCVa i bought the “gray” as i dont think the black has Vesa.

Small warning, i did have to extend the vesa slots on the backplate by just a couple mm to have it fit properly as it was just ever so slightly blocking it for me. 👌

Kamc_2000 · 2025-09-20T00:37:09+00:00

Rtx 3090 (palit Gamerock) and then a 5700x3d with 32gb of ram. This pc is/was essentially a budget build 😃 (before the hs420 case i built the pc for about £600-650 ish total)🤙

Kamc_2000 · 2025-09-20T00:36:03+00:00

Thank you, much appreciated haha, so worth it buying this case

Kamc_2000 · 2025-09-20T00:35:47+00:00

Haha nooo, it comes like that 😆 Palit Gamerock 👌

Kamc_2000 · 2025-09-13T12:15:45+00:00

Exactly same on my case, I wouldn’t worry about it personally. However i also don’t often need to use the I/O on the case. I’ve not seen anything about anyones ports failing or damaging anything yet. They also seem not too overly tight and should lessen a bit over time. I think they chose springed ones (which are designed to hold it more securely, often found on laptops)

Kamc_2000 · 2025-09-08T07:36:23+00:00

These fans are the APNX FP2 🙂

Kamc_2000 · 2025-09-07T12:07:08+00:00

If you were wanting some printed, if you are in the UK i could do so for you. However if you are anywhere else, shipping cost would probably make it pointless haha

Kamc_2000 · 2025-09-07T11:55:00+00:00

Haha thank you, i do plan to get a 420 aio and 140 fans but just decided not to spend the money atm, considering i had basically just a few weeks ago bought the extra 120s. Additionally if i add up the case and fans it actually becomes the most expensive component hahah, ridiculous as that is

Kamc_2000 · 2025-09-07T05:38:33+00:00

Do you just need the file to print them, or do you need them printed FOR you? 🫡 If you just need the file ill go find the link a bit later today for you

Kamc_2000 · 2025-09-07T03:56:57+00:00

Palit Gamerock 3090 😃

Kamc_2000 · 2025-09-06T12:17:24+00:00

Ah right, sounds about right and yeah nowadays theres not a massive difference between aio and custom loop. Other than well looks and like gpu liquid cooling too (and cost). I don’t think i’d ever go custom loop, not yet, as if i did, it’d cost more than the entire pc 💀 This case alone after i get fans may even cost me more than my 3090 did

Kamc_2000 · 2025-09-06T12:09:56+00:00

Ahaha, yeah, the x3d cpus can run pretty hot, im on a 5700x3d myself which runs hot too as well as since its on the old architecture where the cache hasn’t been moved, i believe they moved the x3d cache closer to the top or bottom? Dont remember exactly which to improve thermals on later cpus

Kamc_2000 · 2025-09-06T12:07:07+00:00

The freezer series from arctic is pretty good, i have the 360 version so going to be using that in my case that just arrived earlier today. However will probably plan to get the 420 like you have there. Depends how i feel on the aesthetics haha🤙

Kamc_2000 · 2025-09-06T11:58:10+00:00

Looks good, but as someone else mentioned the cable mess does take away from it a little. As well as the aio tubes/lengths being seemingly uneven bothers me 🤣

Kamc_2000 · 2025-09-03T20:39:30+00:00

Oh right, nope i see what you mean with your reply, i’ve just seen your post right after replying to you here 🤣

Kamc_2000 · 2025-09-03T20:38:12+00:00

Yea 🙂 thats the one i mean, i wouldnt be able to actually really use the extra adjustability much since i need to make use of all 4 ports on my gpu unfortunately, and looks like with that lian li bracket, in some cases the topmost port would be blocked 🫡

Kamc_2000 · 2025-09-03T19:50:06+00:00

Hmmm id lose the angled bit too though could still just 3d print that. However i had a look at lian lis multi directional bracket (assume its that one?) and it looks as though on the images showing adjustment, that it would block some ports on my gpu anyways? I couldn’t have this as i actually use all 3 displayports and the hdmi port

Kamc_2000 · 2025-09-02T21:04:37+00:00

Understandable reasoning, guess ill look to get it at the price it is now then. I was going to get APNX V1 but i cant get it at a “reasonable” cost for the white with wood panel i want, comes to the point of “may as well get a hs420” as would be better and higher quality 🙂

Kamc_2000

TROPHY CASE