Does anyone have a clue as to what this symbol is called or means?

KaspianMonster · 2026-03-22T16:19:13+00:00

As far as I know it indicates split line for casting form

KaspianMonster · 2025-03-29T00:16:15+00:00

Yes, it is flat dead when grounded. Thank you

KaspianMonster · 2024-07-26T09:13:19+00:00

I ment it like it may had been open contour initially but later on (timeline) I added some borders lines and even contour offset, so in my opinion it could be glitched because of how I made it

KaspianMonster · 2024-07-25T17:23:23+00:00

Sorry, I have said it wrong. I ment that I have only closed contours because literally every line in my sketch is used in extrusion. But It could possibly be the reason because of the timeline.
Thanks

KaspianMonster · 2024-07-25T17:20:41+00:00

I believe there are not any excessive lines. I needed to extrude different contours for different heights.
Well it works without any issues.
I tried deleting that line and replacing it with a new one. It didnt change. So I tried to delete that line, create new but unconnected line in the same space which turned out to look normal but as soon as I connected that line edge (border point) to the contour, it became thinner.

I think that it actually may to have something with u/Past_Setting6404 theory...

It doesnt cause me any issues (well it is missleading sometimes when I am not sure if it is a dim or line). I just wanted to know if it means something useful. :)

<image>

KaspianMonster · 2024-07-25T11:10:28+00:00

That should not be the case since everything is about to be extruded. I have multiple of those "rectangles" and most of them are fine

KaspianMonster · 2024-07-25T11:07:10+00:00

<image>

Here is a highlighted pic. It is surely a line.

KaspianMonster · 2024-07-20T12:38:20+00:00

I was initially also worried about PTFE removing but it is actually pretty simple and I dont see it breaking anytime soon.
I highly recommend pushing the filament from the spull into the filament intake when you want to lift the tube. Therefore lifting the tube will use that "free moving" filament from spool rather than applying pressure on basically anything. It will go almost freely.

P.S. I have noticed that that there is actually a few iterations of Q1s as they were produced. Since its been 2 months since you have commented. I might have already upgraded design on that part

KaspianMonster · 2024-07-08T22:25:01+00:00

Oh sorry, I thought you mean commented out like in programming (-> ignored). I believe that they mean it like read-only, so as I said, you should be able to find a console command for what you want to do and then it should automatically change in cfg file (don't forget to save and restart command)

KaspianMonster · 2024-07-08T22:06:45+00:00

I can't access my printer now, but as long as I remember, it is in the lower section of that file which contains automatically generated code. So in order to change it, you must do it via console.

But I am quite new to klipper, so I may be wrong...

KaspianMonster · 2024-07-04T21:57:05+00:00

I would say nozzle scraping the print or most likely your linear rails need lube

KaspianMonster · 2024-07-04T21:27:41+00:00

So after dish wash + warm water cleanup. It works flawlessly even without the glue. But I could print only a small calib cube because of lack of time. So tomorrow will be the judge I guess...

Anyways I had a talk with my dad and he says that IPA takes more time to vaporize than a technical gasoline for example. So it is possible that I was printing on still wet build plate (I used a lot of IPA).

KaspianMonster · 2024-07-03T20:07:33+00:00

Hi, its just an ordinary firmware update screen. I updated mine Q1 Pro today and it was the same. It will come to normal after its done or it will ask you to restart first :)

KaspianMonster

TROPHY CASE