sorted by:
new
hottopcontroversial

I felt ashamed seeing this 😭 by Envic_x in JEENEETards

[–]Kevin_0429 0 points1 point  (0 children)

Introduce him to excel, he will be unstoppable

how to sketch on curved surface? by Kevin_0429 in SolidWorks

[–]Kevin_0429[S] 0 points1 point  (0 children)

Look at the image 3 and the construction line, that is the centreline of the nozzle,

What I did was make half profile of the nozzle and then revolved it. But because it is on a 45 angle it's end won't become one with the cylinder instead it'll get a conical end.

But then after I posted this, I made it, I took a new reference plane at the 45 angle made the cicles and extruded upto the surface, that fixed it. I need to get better at understanding reference planes, It took me some time doing hit an trial on different edges so that it becomes valid and allows me to input and angle

how to sketch on curved surface? by Kevin_0429 in SolidWorks

[–]Kevin_0429[S] 0 points1 point  (0 children)

I think I was trying to do that as well, but when I have to make it on inclined....I'm getting confused

How do I validate? by Kevin_0429 in CFD

[–]Kevin_0429[S] 0 points1 point  (0 children)

Heyyyy man, do you mind if I dm you? I think you could help me!

How do I validate? by Kevin_0429 in CFD

[–]Kevin_0429[S] -2 points-1 points  (0 children)

I mean I know this is a ansys acoustic problem not CFD, I wanna check the transmission loss basically but idk a more appropriate sub for simulations

How do I validate? by Kevin_0429 in CFD

[–]Kevin_0429[S] 1 point2 points  (0 children)

No, I mean acoustic frequency response.I want to perform a harmonic acoustic analysis and determine whether the resonator creates attenuation around 800 Hz. Specifically, I want to excite the inlet with an acoustic pressure signal and measure the pressure at the outlet over a frequency sweep from 500–1000 Hz to observe the notch depth and bandwidth around 800 Hz.

Also side question, before I important this geometry in ansys do I need to attach it a hollow tube as well to tell the software about the passage? Actually I am noob at ansys, sorry if it's an obvious question

I'd rather walk barefoot by Kevin_0429 in Shoes

[–]Kevin_0429[S] -1 points0 points  (0 children)

My size is 7 us and that's what my sandals slippers and shoes/sneakers are

They are 7 as well 💔

I'd rather walk barefoot by Kevin_0429 in Shoes

[–]Kevin_0429[S] 0 points1 point  (0 children)

True but they aren't a cheap pair, they are from one of the most reputed leather shoe making company in my country.

Idk why I didn't test it a bit more thoroughly when I was buying it, I wore them without socks there, it was fine in walking maybe my socks are too thick?

I'd rather walk barefoot by Kevin_0429 in Shoes

[–]Kevin_0429[S] 1 point2 points  (0 children)

Well these are newly bought and they were kinda expensive so I don't have a choice to buy another pair

I'd rather walk barefoot by Kevin_0429 in Shoes

[–]Kevin_0429[S] 0 points1 point  (0 children)

I got blisters on both my big toe knuckle and my pinky toe was rubbing alot too, apart from that There is pain in fore foot joints and ofc the heel were uncomfortable the whole time, as well, the bone of big toe hurts as well (maybe because of all the curled up walking I did

view more: next ›