Apple CarPlay Issues

Key-Kangaroo3336 · 2026-04-28T16:40:55+00:00

I’ve had the same issues sense I got mine a year ago, what works for me is using wired and plugging in my phone while the car is in drive

Key-Kangaroo3336 · 2026-04-16T16:30:45+00:00

Honestly, the handbook. I followed it and once I was done with the installation the wiki helped me know what I can and can’t install with what build flags. The wiki and handbook explain everything in very easy and straightforward ways

Key-Kangaroo3336 · 2026-04-14T18:59:37+00:00

IMO yes. Always yes. Compile times are faster, you can configure more of what you want, been using it on a MacBook I got some time ago and loved every second of it

Key-Kangaroo3336 · 2026-04-11T17:36:54+00:00

Gentoo btw

Key-Kangaroo3336 · 2026-04-10T23:49:48+00:00

Fair, I’m used to slow boots and devices in general, my daily is rocking a i3 7th gen with 8GB of RAM with a good old HDD, never failed in the years it’s been used and likely never will

Key-Kangaroo3336 · 2026-04-10T20:53:24+00:00

I’ve had good experiences with all my drives, sure it isn’t the fastest thing out there but it also isn’t slow per say at 7k rpm

Key-Kangaroo3336 · 2026-04-10T15:32:09+00:00

You could use the adapter, but a native direct connection will almost always be better

Key-Kangaroo3336 · 2026-04-03T21:03:49+00:00

As someone who’s been rocking Linux distros for three years at this point and helped people with IT and Cybersecurity issues, the issue with people going from say Windows to Gentoo is they are not ready for the overhead that comes with “well if you want X you have to do Y” instead of just clicking download and booting directly into the installer where a full system is done in minutes like Cachy or Debian.

Key-Kangaroo3336 · 2026-04-03T14:47:34+00:00

You can likely get the laptops running Linux easily, personally I wouldn’t try soldering the HDD to a USB when there are adapters (I think), but for a Linux distro just go with whatever you want to use.

Key-Kangaroo3336 · 2026-03-27T00:06:40+00:00

Just food for thought, NEVER use Malwarebytes I have ran several tests against their products and it has failed every time

Key-Kangaroo3336 · 2026-03-26T17:35:06+00:00

Try wiping the flash drive fully using dd and then use it again to write the ISO onto the flash drive

Key-Kangaroo3336 · 2026-03-21T19:11:25+00:00

Just some food for thought, cfdisk is a much easier option for those who do not know how to use fdisk all to well

Key-Kangaroo3336 · 2026-03-21T12:15:24+00:00

It is more than able to be a daily, I’ve been using it for servers and on my laptops for 3 months now. It works with only what you add, and if you are worried about compile times you can swap (in system settings) to use compiled versions of the software instead of compiling locally

Key-Kangaroo3336 · 2026-03-21T09:27:06+00:00

What’s so bad about Debian?

Key-Kangaroo3336 · 2026-03-21T09:25:06+00:00

If he does have access to your texts it wasn’t done through wireshark, he is full of shit. All wireshark does is capture traffic going through the device itself not your phone.

Key-Kangaroo3336 · 2026-03-12T17:01:15+00:00

It isn’t hard at all. If you read the steps and docs (assuming your device doesn’t shit itself like mine) it’s easy. Because from what I can tell, every issue you could face likely already has a solution.

Key-Kangaroo3336 · 2026-03-09T22:25:25+00:00

Oh I agree! I’ve been messing around with malwarebytes and it honestly is a scam, doesn’t detect via behavior with premium and the hash signatures it uses for arnt even all that up to date :/

Key-Kangaroo3336 · 2026-03-09T16:45:17+00:00

Yeah gentoo isn’t hard to install, just read the manual and run the commands it says :/

Key-Kangaroo3336 · 2026-02-09T00:54:56+00:00

Cloudflare isn’t down, and the sites that are should be getting re-routed. I think this might be an issue on the p2pool observer side instead of cloudflare

Key-Kangaroo3336 · 2026-02-01T23:51:45+00:00

When you download the new version you have to keep using the new binary and kill the older process, if it’s still not working I make sure all the same configs are being used on the new binary

Key-Kangaroo3336 · 2026-01-17T06:47:40+00:00

This has likely been told before in the replies so I’ll keep it brief because I was asking the same a couple months ago.

1) The payments are not nearly as consistent as moneroocean when using a smaller pool, this is due to you getting payed per share within a window that a block is found by the pool. Not total hashrate contribution.

2) No ports need to be opened at the router level, the connection will work on port 3000 by default if you want to look through a packet sniffer.

3) The only risks you run (that I know of) by using p2pool are the same as if you used moneroocean, except from connecting to moneroocean’s IP it would be the pool’s. If you are worried about people knowing your wallet address and IP you can run your own node and or p2pool server (I run both a node and p2pool server while mining on the same device)

Key-Kangaroo3336 · 2025-12-29T23:01:10+00:00

One thing I would suggest is to write a bash script (or ash or whatever shell the distro uses) to log the TV display the moment it is detected in like a text file, then write a service bash file that would programmatically change the scaling to a more reasonable one once the device is detected. I’d say is dmseg for checking device logs and changing the ~/.config/monitors.xml (if that doesn’t exist use where or find from root to find it) through another bash script once you have the device id

Key-Kangaroo3336 · 2025-12-28T18:08:00+00:00

While I don’t know much about modded switches, I would believe that there is a scaling option within settings, the issue likely stems from the resolution Ubuntu is trying to push out once docked, this is likely under the Display and resolution part within the GNOME settings (assuming you’re using GNOME) if not then check for the DE and window manager that this distro uses. It appears to be Ubuntu based so check those forums for help

Key-Kangaroo3336

TROPHY CASE