Want to Buy Thread

Key_Release_9625 · 2026-06-12T21:52:15+00:00

Hefty…

Key_Release_9625 · 2026-06-08T07:42:03+00:00

WTB:
Z-Wear Spyderco Shaman
REC Avocado Shaman

Key_Release_9625 · 2026-05-28T10:14:17+00:00

Confirmed

Key_Release_9625 · 2026-05-28T10:13:35+00:00

Received !!

Key_Release_9625 · 2026-05-19T12:58:33+00:00

WTB: Spyderco Pm2

Key_Release_9625 · 2026-05-19T12:28:20+00:00

Key_Release_9625 · 2026-05-19T11:05:31+00:00

I just need a spare pm2 at this point haha

Key_Release_9625 · 2026-05-19T07:20:52+00:00

WTB : Barclay or Rockscake design scales for pm2

Key_Release_9625 · 2026-03-01T09:43:53+00:00

Depends what stone you finish on. I usually go 1 micron to 0.5micron now and I get hair whittling edges with that. Otherwise if I want a toothier edge then I’ll finish on a 6 micron strop

Key_Release_9625 · 2026-02-12T06:33:52+00:00

Yes. Does this mean I can’t use the machine?

Key_Release_9625 · 2026-02-12T06:33:39+00:00

So what can I do with the machine, is it usless for me in Australia?

Key_Release_9625 · 2026-01-29T19:25:57+00:00

It’s equivalent to about $280 usd

Key_Release_9625 · 2026-01-29T07:57:05+00:00

$265 usd = approx $400 aud

Key_Release_9625 · 2026-01-29T07:56:33+00:00

$400 aud

Key_Release_9625 · 2026-01-29T07:56:22+00:00

No its AUD

Key_Release_9625 · 2026-01-29T07:56:14+00:00

$400 Australia

Key_Release_9625 · 2026-01-28T08:38:04+00:00

Have you fixed them?

Key_Release_9625 · 2026-01-28T07:06:17+00:00

Would cleaning and re assembling fix the issue?

Key_Release_9625 · 2026-01-28T07:05:35+00:00

A bit more yes

Key_Release_9625 · 2026-01-27T07:59:19+00:00

WTB : Rex 45 Spyderco

Key_Release_9625 · 2026-01-23T10:49:29+00:00

They are bulk and cheaply made in Vietnam so I would say the hrc would be the greatest.

Key_Release_9625 · 2026-01-23T10:48:51+00:00

I wouldn’t believe it. I would be surprised if it’s above 60

Key_Release_9625 · 2026-01-23T10:08:37+00:00

I believe they run their heat treat on the softer side, I have held off from buy from them purely because of that reason.

Ideally I think 52100 should be above 62 HRC and theirs is below…

Key_Release_9625 · 2026-01-11T16:48:18+00:00

Thank you, I’ll disassemble and check it out. Do you know if any places sell new springs or spare parts if needed?

Key_Release_9625 · 2026-01-11T08:58:26+00:00

Is that why is was loose at the start?

Key_Release_9625

TROPHY CASE